Hettich EBA 280 Скачать руководство пользователя страница 26

Страница: 26 / 45

26/45

Rev. 01 / 11.2022

AB1101EN_SA

20.2 Acoustic

signal

The acoustic signal sounds:



after a malfunction occurs in a 2-second interval.



after ending the centrifugation run and the rotor is at a standstill in a 30-second interval.

The acoustic signal is ended by pressing any key.

If the rotor is at a standstill, the acoustic signal can be set as follows:

The procedure can be aborted at any time by pressing the

STOP

OPEN

key. In this case, the settings are not stored.



Press and hold the button for eight
seconds.

PROG

t/min:s

RPM





Press the key until the following is
displayed:

PROG

t/min:s

RPM



START

PULSE



Press the key.

End beep :

Acoustic signal after ending

the centrifugation run.

off :

Signal deactivated.

on :

Signal activated.

PROG

t/min:s

RPM

PROG

t/min:s

RPM





With the keys, set

off

PROG

t/min:s

RPM

PROG

t/min:s

RPM





Press the key.

Error beep :

Acoustic signal after a

malfunction occurs.

off :

Signal deactivated.

on :

Signal activated.

PROG

t/min:s

RPM

PROG

t/min:s

RPM





With the keys, set

off

PROG

t/min:s

RPM

PROG

t/min:s

RPM





Press the key.

Beep volume :

Volume of the acoustic

signal.

min :

soft

mid :

medium

max :

loud

PROG

t/min:s

RPM

PROG

t/min:s

RPM

PROG

t/min:s

RPM





With the keys, set

min

mid

max

PROG

t/min:s

RPM

PROG

t/min:s

RPM

PROG

t/min:s

RPM



Continued on next page

Содержание EBA 280














































Результаты поиска

Содержание EBA 280

Отзывы:

Похожие инструкции для EBA 280

Бренды по названию

Популярные бренды

Hettich EBA 280, Руководство по эксплуатации

Результаты поиска

Содержание EBA 280

Отзывы:

Похожие инструкции для EBA 280

Бренды по названию

Популярные бренды