Hettich EBA 280 Скачать руководство пользователя страница 17

Страница: 17 / 45

AB1101EN_SA

Rev. 01 / 11.2022

17/45

Example:
RPM display (RPM)

Example:
RCF display ( RCF )

RCF



Press the key to activate the RPM display
(RPM) or the RCF display ( RCF ) as
needed. The LED above the key is
illuminated if the RCF display ( RCF ) is
activated.

PROG

t/min:s

RPM

PROG

t/min:s

RPM





Keep pressing the key until the desired
centrifugation parameter is displayed.
Example:

t/min :

Runtime, minutes.

PROG

t/min:s

RPM

PROG

t/min:s

RPM





Set the desired value with the keys.

PROG

t/min:s

RPM

PROG

t/min:s

RPM







Input all the desired centrifugation
parameters in succession.

PROG

t/min:s

RPM

PROG

t/min:s

RPM





Press the key until the following is
displayed:

PROG STO :

Program location where the

centrifugation parameters are stored.

PROG

t/min:s

RPM

PROG

t/min:s

RPM





Set the desired program location with the
keys.

PROG

t/min:s

RPM

PROG

t/min:s

RPM



START

PULSE



Press the key.
The centrifugation parameters are stored
at the program location.

PROG

t/min:s

RPM

PROG

t/min:s

RPM

PROG

t/min:s

RPM

PROG

t/min:s

RPM

Содержание EBA 280














































Результаты поиска

Содержание EBA 280

Отзывы:

Похожие инструкции для EBA 280

Бренды по названию

Популярные бренды

Hettich EBA 280, Руководство по эксплуатации

Результаты поиска

Содержание EBA 280

Отзывы:

Похожие инструкции для EBA 280

Бренды по названию

Популярные бренды