Heras HGD230 Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 146

background image

EN – Translation of the original user manual - 2.1 | 2019

82

•

Switch on the power supply to the motor drive while a chipcard is

inserted.

•

Indication: "I2C SmartCard".

•

Turn the selector switch in a clockwise direction; you will now see the

message:

"copy Card->CTRL"

•

Press the selector switch to start copying: "copy …."

•

When copying is finished the following message is displayed: "copy

DONE".

•

Removing the card from the reader restarts the motor drive with the

newly loaded parameters.

Note!: Errors that occur during copying are reported by means of "Card
Comm. ERROR".

You can try to read the chipcard again by turning the selector switch and pressing
it. If this does not work, all parameters will be erased by the software when the
chipcard is removed. The HMD230 shows "Init/Clear EEPROM" and then "Load
Parameter". The contents of a card have to be read then again. The motor drive
does not work without correct parameters.

7.19

SUPPORT DURING DIAGNOSIS

The HMD230 has a diagnostics menu that makes putting the motor drive into use
and troubleshooting easier.

7.19.1

Version display

The motor drive version can be displayed as follows:

•

Menu: "Identification", "Master Version": the figures and the combination

of numbers shown clearly identifies the software version used.

•

Menu: "Identification", "Gate profile": the text shown is the designation of

the gate for which the master drive, the software and the parameters
stored have been defined.

•

Menu: „Identification“, „Serial number“: The serial number of the control

is shown here.

The following version parameters are visible after entering the right password:

«
...
80
81
82
83
84
...
»

Содержание HGD230



















































































































































Отзывы:

Нет отзывов

Похожие инструкции для HGD230

Бренд: G-Force Страницы: 16

Silent Drive MR650EVO

Бренд: Merlin Страницы: 20

Бренд: Dieffematic Страницы: 10

Бренд: Gator Страницы: 26

LiftMaster Professional 78LM

Бренд: Chamberlain Страницы: 2

Бренд: CAME Страницы: 12

Бренд: CAME Страницы: 13

Бренд: CAME Страницы: 128

Бренд: LockMaster Страницы: 2

Бренд: Upswung Страницы: 50

Бренд: SEA Страницы: 8

Бренд: Elite Страницы: 23

Бренд: Toastmaster Страницы: 9

GDO-4 EasyRoller

Бренд: Automatic Technology Страницы: 20

Бренд: CAME Страницы: 32

Бренд: Beninca Страницы: 28

Бренд: Rollerdor Страницы: 20

Бренд: CAME Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды