13
STEP 6CS – No Hard Water Bypass Enabled - Selection requires that a connection to a
Motorized Alternator Valve (MAV) is made to the two pin-connector labeled ALTERNATOR MAV
DRIVE located on the printed circuit board. The MAV will be driven closed before the first re-
generation cycle that is not FILL or FILTERING, and be driven open after the last regeneration
cycle that is not FILL. NOTE: If the control valve enters into an error state during regeneration
mode, the no hard water bypass valve will remain in its current state until the error is corrected
and reset. Press NEXT to go to Step 10CS.
STEP 7CS – Configuring the Control Valve for Separate Source Operation - Select
Separate Source Enabled for control operation. For separate source operation, the three wire
connector is not used. Selection requires that a connection to a MAV is made to the two pin
connector labeled ALTERNATOR MAV DRIVE located on the printed circuit board. The C
port of the MAV must be connected to the valve inlet and the A port connected to the separate
source used during regeneration. The B port must be connected to the feed water supply.
When set to Separate Source Enabled the MAV will be driven closed before the first regeneration
cycle, and be driven to open after the last regeneration cycle.
NOTE: If the control valve enters into an error state during regeneration mode, the MAV will
remain in its current state until the error is corrected and reset. Press NEXT to go to Step
10CS.
STEP 8CS – Configuring the Control Valve for Water Reclamation Mode - Select Reclama-
tion Enabled for control operation. Motorized Alternating Valve will advance to Bypass at a set
time after the beginning of regeneration, and return to Service after a set duration.
The start of regeneration is defined as the first cycle that is not FILL or FILTERING. The
Alternating MAV will transition back to Service after the completion of the preset duration time,
labeled Reclaim Duration. Three reclaim events are possible. Select either Reclaim Enabled,
Reclaimed 2x for two events and Reclaim 3X for three separate reclaim events.
ENABLED
NO HARD BYPASS
SET
STEP 6CS
SEPARATE SOURCE
SET
STEP 7CS
ENABLED
RECLAIM
SET
STEP 8CS
ENABLED
STEP 5CS
DELAYED RINSE & FILL
SET
OFF
MIN
STEP 5CS – This option delays the last two cycles of regeneration (only "Rinse" and "Fill").
Filter must be programmed as post fill. This feature splits the regeneration into two por-
tions. The first portion of the regeneration will start immediately and all programmed cycles
before the "Rinse" and "Fill" cycles will be performed. After all programmed cycles before
"Rinse" and "Fill" are completed the control valve will drive to the stand-by position (display-
ing "Delayed Rinse + Fill Pending"). When the volume of the on-line unit is depleted to 10% of
its programmed capacity, the control valve will be triggered to finish the second portion of the
regeneration and complete the "Rinse" and "Fill" cycles and return to Service and be placed
into Standby mode, to wait to come on-line for service. Press NEXT to go to Step 10CS.
➔
➔
➔
➔
Use the
or
buttons to select minutes after start of regeneration to activate MAV to
reclaim position for 1st reclaim event. Press NEXT to set duration of reclaim.
Use the
or
buttons to select minutes of 1st reclaim duration. Press NEXT to go
to next reclaim event if more than one event is selected. Press NEXT to go to Step
10CS. If only one reclaim event is selected.
Only displays if more than one reclaim event if selected. Use the
or
buttons to
select the number of minutes after start of regeneration for second reclaim event.
Press NEXT to program second reclaim duration. Use the
or
buttons to set
length of second duration.
Press NEXT to program third reclaim event or to go to Step 10CS.
MAV RECLAIM START
SET
10:00
➔
MIN
RECLAIM DURATION
SET
15:00
➔
MIN
MAV RECLAIM 2 START
SET
26:00
➔
MIN
RECLAIM 2 DURATION
SET
10:00
➔
MIN
Содержание ProMate-6.0
Страница 27: ...27 NOTES...
