Heise PTE-2 Скачать руководство пользователя страница 60

Страница: 60 / 88

IMPORTANT NOTE for INTRINSICALLY SAFE APPROVED

VERSIONS OF THE Hand Held Calibrator
1. When access port is open, the device is not operating in

an Intrinsically Safe mode. As such it is not possible to

use the HHC in a hazardous area whenever the USB port

is exposed or if the port access door is not secured with

Philip’s head screw.

2. When using an Intrinsically Safe approved HHC in a

non-hazardous environment, the USB protection adapter

must be used to connect the HHC to a PC’s USB port.

Failure to install the USB protection adaptor can result in

damage to the electronics which could render the HHC no

longer intrinsically safe.

Driver Installation

If the PC being used together with the HHC does not already

have the proper drivers installed it will be necessary to install a

driver to enable communication.

The HHC need not be powered on for the driver installation.

Place the memory stick that came with the HHC in one of the

PCs USB ports.

SECTION 15 m. i.

USB Cable Installation Cont.

SECTION 15 m. ii.

Driver Installation

Содержание PTE-2

























































































Результаты поиска

Содержание PTE-2

Отзывы:

Похожие инструкции для PTE-2

Бренды по названию

Популярные бренды

Heise PTE-2, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание PTE-2

Отзывы:

Похожие инструкции для PTE-2

Бренды по названию

Популярные бренды