Heise PTE-2 Скачать руководство пользователя страница 12

Страница: 12 / 88

The base unit functions as a host for the Quick-Select pres-

sure and temperature modules. The base unit includes two

bays for installation of pressure or temperature modules, an

LCD graphic display with back light, a key pad, a USB micro B

receptacle for communication with a PC, an SD memory card

slot and banana jack connections for DC voltage supply and

signal monitoring. The enclosure is rated to IP65 water resis-

tant.

When pressure and or temperature modules are installed and

the base unit is powered on, it will briefly display the brand

name, data regarding installed modules. Then the HHC will

go into measurement mode where it will display up to three

values as well as their respective engineering units of measure.

The base unit is pre-programmed with twelve units of pres-

sure measurement, four units of temperature measurement,

DC voltage 0-30 VDC, DC current 0-20 ma and also allows the

user to program a custom pressure unit of measure. In mea-

surement mode, the display will show Battery status, USB con-

nection status, one or two vertical bar graph indicators indicat-

ing percentage of full scale pressure and other user interface

and warning messages when applicable.
The calibrator is equipped with internal memory capable of

storing up to 16,000 records. Datalogs can be transferred to an

optional on board SD memory card to clear internal memory

and allow further data collection. Datalogs can be transferred

to a PC from the SD card and are presented in .csv files which

can be opened by Microsoft Excel software.

-0.12

in H 2 0

0.000

volts

-0.001

PSi

POWER

MENU KEY

CH1 MODULE-
ENGINEERING UNITS

CH2 MODULE
READING

CH2 MODULE/
BAR GRAPH

CH1 MODULE-
BAR GRAPH

SD CARD
INDICATOR

USB INDICATOR

24VDC
POWER SUPPLY
INDICATOR

UNIT OF PRESSURE

CH1 MODULE
READING

ZERO FUNCTION

BACK LIGHT

TARE/
RIGHT ARROW

FLIP DISPLAY/
DELETE

ESCAPE

DAMPING/
LEFT ARROW

MILLIAMP/VOLT
SELECT INSERT

VOLT/MILLIAMP
INDICATOR

EXTERNAL
VOLT/MILLIAMP
READING

USB/BATTERY
POWER INDICVATOR

MIN/MAX FUNCTION/
DOWN ARROW

PORT SELECT/
UP ARROW

DATA STORE/
ENTER

CHANNEL 1
MODULE

CHANNEL 2
MODULE

SECTION 4

BASE UNIT OVERVIEW

Содержание PTE-2

























































































Результаты поиска

Содержание PTE-2

Отзывы:

Бренды по названию

Популярные бренды

Heise PTE-2, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание PTE-2

Отзывы:

Бренды по названию

Популярные бренды