Heinzmann Programmer 2 Скачать руководство пользователя страница 51

Страница: 51 / 57

7 Error Handling

Programmer PG 02

quadrant-operation.
- Check reference values and error limits for feeedback
- Programme feedback error limits
1972

FeedbackErrorLow

= 0

1973

FeedbackErrorHigh

= 65535

store values, restart governor by reset

and repeat automatic calibration.

- Set error limits again.

Note:

These parameters are implemented only in the PRIAMOS III series.

3061 ErrDigiIO1

3161 SErrDigiIO1

3062 ErrDigiIO2

3162 SErrDigiIO2

3063 ErrDigiIO3

3163 SErrDigiIO3

3064 ErrDigiIO4

3164 SErrDigiIO4

Cause:

Hardware component has detected overload.

Response:

- Error message.

Actions:

- Check digital IOs.
- Clear error.

Note:

These parameters are implemented only in the HELENOS series.

3065 ErrISOCommLine

3165 SErrISOCommLine

Cause:

Error at hardware component.

Response:

- Communication is impossible.

Actions:

- Restart governor by reset.
- Notify HEINZMANN.

Note:

These parameters are implemented only in the HELENOS series.

3070 ErrCanBus1

3170 SErrCanBus1

Cause:

The CAN controller for CAN bus 1 reports errors such as BusStatus,
ErrorStatus or DataOverrun. In spite of re-initializing the controller it is not
possible to eliminate the errors permanently.

Response:

- Depending on the specific application.

Action:

- Check CAN module.
- Check CAN connection.

Содержание Programmer 2


























































Результаты поиска

Содержание Programmer 2

Отзывы:

Бренды по названию

Популярные бренды

Heinzmann Programmer 2, Руководство пользователя

Результаты поиска

Содержание Programmer 2

Отзывы:

Бренды по названию

Популярные бренды