manualshive.com logo in svg

Heatilator NNXT33-IFT, Руководство по установке, Страница: 7 / 67

Поделиться
Скачать
Heatilator NNXT33-IFT Скачать руководство пользователя страница 7

7

Heatilator  •  NNXT33-IFT, NNXT33L-IFT, NNXT36-IFT, NNXT36L-IFT Installation Manual  •  2628-980  Rev. C  •  8/20

D.  Inspect Appliance and Components

WARNING! Risk of Fire or Explosion! 

Damaged parts 

could impair safe operation. 

DO NOT i

nstall damaged, in

-

complete or substitute components. Keep appliance dry.

WARNING! Risk of Fire, Explosion or Electric Shock! 

DO NOT

 use this appliance if any part has been under 

water.  Call  a  qualified  service  technician  to  inspect  the 

appliance and to replace any part of the control system 

and/or gas control which has been under water.

•  Carefully remove the appliance and components from 

the packaging. 

• The vent system components and decorative barrier 

fronts may be shipped in separate packages. 

•  If packaged separately, the log set and appliance grate 

must be installed. 

•  Report to your dealer any parts damaged in shipment.
•  This product is factory-equipped with an IntelliFire Touch 

remote control, which was paired to the appliance at the 

factory.  This specific remote control needs to remain with 

the contents of the manual bag.  Do not install batteries 

in the remote control until performing the final appliance 

setup and checklist. 

Hearth & Home Technologies disclaims any responsibility 

for, and the warranty will be voided by, the following actions:
•  Installation and use of any damaged appliance or vent 

system component.

•  Modification of the appliance or vent system.
•  Installation other than as instructed by Hearth & Home 

Technologies.

•  Improper positioning of the logs/media (as applicable) or 

the glass assembly.

•  Installation and/or use of any component part not approved 

by Hearth & Home Technologies.

Содержание NNXT33-IFT




































































Отзывы:

Нет отзывов