Heatilator NNXT33-IFT Скачать руководство пользователя страница 60

Страница: 60 / 67

Heatilator • NNXT33-IFT, NNXT33L-IFT, NNXT36-IFT, NNXT36L-IFT Installation Manual • 2628-980 Rev. C • 8/20

13-5/8 IN.

13-11/16 IN.

1-3/4 IN.

4 IN.

5-7/8 IN.

3-11/16 IN.

12-1/8 IN.

TOP VIEW

SIDE VIEW

Optional Wire Harness

DESCRIPTION

PART NUMBER

10 FT PV Wire Harness

PVI-WH10

20 FT PV Wire Harness

PVI-WH20

40 FT PV Wire Harness

PVI-WH40

60 FT PV Wire Harness

PVI-WH60

80 FT PV Wire Harness

PVI-WH80

100 FT PV Wire Harness

PVI-WH100

A. Vent Components Diagrams

(continued)

PVV-SLP

Vertical Power Vent

Note:

A wire harness is required to power the PVV-SLP and connect it to the appliance. It is ordered separately from

the PVV-SLP. Contact your dealer to order.

Note:

The PVV-SLEEVE-12 and/or PVV-SLEEVE-48 is required to be installed with the PVV-SLP. It is ordered

separately from the PVV-SLP. Contact your dealer to order.

DECORATIVE TERMINATIONS/SHROUDS

Only use listed decorative termination caps/shrouds with Hearth & Home Technologies approved venting

systems.
This applies to both DVP and SLP venting systems.

Decorative Terminations Caps/Shrouds

DTO134

DTO146

DTS134

DTS146

LDS33

LDS46

LDS-BV

Figure 12.6 Vent Components

Note:

The PVV-SLP requires one of the following options to be installed on this appliance.

Option A: IFT-RC400 and/or IFT-WFM, IFT-ACM and IntelliFire App that can be downloaded from the app store.

Option B: IFT-RC150, IFT-ACM, IFT-WFM and an IntelliFire App that can be downloaded from the app store. These

accessories are purchased separately from the PVV-SLP. Contact your dealer to order.

Содержание NNXT33-IFT




































































Результаты поиска

Содержание NNXT33-IFT

Отзывы:

Heatilator NNXT33-IFT, Руководство по установке, Страница: 60 / 67

Результаты поиска

Содержание NNXT33-IFT

Отзывы: