manualshive.com logo in svg

Heatilator NNXT33-IFT, Руководство по установке, Страница: 42 / 67

Поделиться
Скачать
Heatilator NNXT33-IFT Скачать руководство пользователя страница 42

Heatilator  •  NNXT33-IFT, NNXT33L-IFT, NNXT36-IFT, NNXT36L-IFT Installation Manual  •  2628-980  Rev. C  •  8/20

42

Figure 7.15  Venting Through the Wall

INTERIOR

HEAT SHIELD OR

EXTENDED

HEAT SHIELD

WALL SHIELD

FIRESTOP

HEAT SHIELD

1-1/2 IN. (38 MM) MIN.

OVERLAP

SHEATHING

VENT DEPTH FROM BACK OF APPLIANCE TO

OUTSIDE SURFACE OF EXTERIOR WALL

(SEE CHART BELOW)

SLIP SECTION

CAN BE EXTENDED

INNER VENT

OUTER VENT

EXTERIOR

Note: 

When using termination caps with factory-supplied 

heat shield attached, no additional wall shield firestop is 

required on the exterior side of a combustible wall.

Install Horizontal Termination Cap (DVP and 

SLP Pipe)

WARNING! Risk of Fire! 

The telescoping flue section of 

the termination cap MUST be used when connecting vent.

• 1-1/2 (38 mm) minimum overlap of flue telescoping 

section is required.

Failure to maintain overlap could cause overheating and 
fire.

•  Vent termination must not be recessed in the wall. Siding 

may be brought to the edge of the cap base. 

• Flash and seal as appropriate for siding material at 

outside edges of cap.

• When installing a horizontal termination cap, follow 

the cap location guidelines as prescribed by current 

ANSI Z223.1

 and 

CAN/CGA-B149

 installation codes 

and refer to Section 4 of this manual.

CAUTION! 

Risk of Burns! 

Local codes may require in

-

stallation of a cap shield to prevent anything or anyone 

from touching the hot cap.

NOTICE: 

For  certain  exposures  which  require  superior 

resistance to wind-driven rain penetration, a flashing kit 

and HRC caps are available.  When penetrating a brick 

wall, a brick extension kit is available for framing the brick.

Cap Specification Chart (depth without using additional pipe sections)

NNXT Series

DVP-TRAPK1 

Top Vent Depth

DVP-TRAP1 

Rear Vent Depth

DVP-TRAPK2 

Top Vent Depth

DVP-TRAP2 

Rear Vent Depth

SLP-TRAP1 

Top Vent Depth

SLP-TRAP2 

Top Vent Depth

4 1/2 to 6 3/8 in.

3 to 4 7/8 in.

6 7/8 to 10 7/8 in. 5 3/8 to 9 3/8 in.

2 to 3 7/8 in.

4 3/8 to 8 3/8 

in.

DVP-HPC1 

Top Vent Depth

DVP-HPC1 

Rear Vent Depth

DVP-HPC2 

Top Vent Depth

DVP-HPC2 

Rear Vent Depth

4 1/2 to 6 5/8 in.

3 to 5 1/8 in.

6 5/8 to 10 3/4 in. 5 1/8 to 9 1/4 in.

DVP-TRAP1 can adjust 1 1/2 in. (3 1/8 to 4 5/8)
DVP-TRAP2 can adjust 4 in. (5 3/8 to 9 3/8)
SLP-TRAP1 can adjust 1 5/8 in. (3 1/8 to 4 3/4)
SLP-TRAP2 can adjust 4 in. (5 1/4 to 9 1/4))
DVP-HPC1 can adjust 2 1/8 in. (4 1/4 to 6 3/8)
DVP-HPC2 can adjust 4 1/8 in. (6 3/8 to 10 1/2)

Содержание NNXT33-IFT




































































Отзывы:

Нет отзывов