Heatilator NNXT33-IFT Скачать руководство пользователя страница 38

Страница: 38 / 67

Heatilator • NNXT33-IFT, NNXT33L-IFT, NNXT36-IFT, NNXT36L-IFT Installation Manual • 2628-980 Rev. C • 8/20

Figure 7.4 Seams

Note:

Make sure that the

seams are not aligned to prevent

unintentional disconnection.

INCORRECT

CORRECT

Required Commercial, Multi-family (Multi-level exceeding

two stories), or High-Rise Applications

All outer pipe joints must be sealed with 100% silicone

(300 ºF minimum continuous exposure rating), including

the slip section that connects directly to the horizontal

termination cap.

• Apply a bead of silicone sealant (300 ºF minimum con

tinuous exposure rating) inside the female outer pipe

joint prior to joining sections. See Figure 7.1.

Apply a bead of silicone sealant (300 ºF minimum con

tinuous exposure rating) to the outside of connecting

joint after joining sections

Apply aluminum foil tape (300 ºF minimum continu

ous exposure rating) to the outside of connecting joint

after joining sections. On horizontal pipe runs, it is

recommended that the tape seam is positioned on the

bottom side of the vent pipe.

• Only outer pipes need to be sealed. All unit collar, pipe,

slip section, elbow and cap outer flues shall be sealed

in this manner, unless otherwise stated.

Assemble Vent Sections (SLP Only)

To attach the first vent component to the starting collars

of the appliance:

• Attach a DVP-SLP24 adapter to the starting collar of the

appliance.

• Lock the vent components into place by sliding the pipe

section onto the collar.

• Align the seam of the pipe and seam of collar to allow

engagement. Rotate the vent component to lock into

place. Use this procedure for all vent components. See

Figure 7.5.

• Slide the gasket over the first vent section and place it

flush to the appliance. This will prevent cold air infiltration.

Caulk with a minimum of 300 ºF continuous exposure

rating may be used to hold the part in place.

• Continue adding vent components, locking each

succeeding component into place.

• Ensure that each succeeding vent component is securely

fitted and locked into the preceding component.

Figure 7.5 Adding Venting Components

WARNING! Risk of Fire or Explosion! DO NOT

break

silicone seals on slip sections. Use care when remov-

ing termination cap from slip pipe. If slip section seals

are broken during removal of the termination cap, vent

could leak.

Note: Align seams to engage pipe,

then rotate counterclockwise to lock

Содержание NNXT33-IFT




































































Результаты поиска

Содержание NNXT33-IFT

Отзывы:

Heatilator NNXT33-IFT, Руководство по установке, Страница: 38 / 67

Результаты поиска

Содержание NNXT33-IFT

Отзывы: