Heatilator NNXT33-IFT Скачать руководство пользователя страница 50

Страница: 50 / 67

Heatilator • NNXT33-IFT, NNXT33L-IFT, NNXT36-IFT, NNXT36L-IFT Installation Manual • 2628-980 Rev. C • 8/20

Non-combustible Mantel and Wall

Projections for use with Simon Fronts

Only decorative barrier fronts certified for use with this

appliance model may be used. Contact your dealer for a

list of decorative fronts that may be used. The finishing

material thicknesses allowed are noted below.

FLUSH WITH FIREPLACE OPENING (TOP OF HOOD)

30 in. minimum

to ceiling

18 in.

Figure 10.4 Non-Combustible Mantel Leg or Wall Projections

(Acceptable on both sides of opening)

Non-Combustible Mantel Legs or Wall Projections -
Use with Simon Fronts

Figure 10.3 Minimum Vertical and Maximum Horizontal

Dimensions for Non-Combustible Mantels

TOP OF

APPLIANCE

DRYWALL

FIREPLACE OPENING

18 in.

See Dimension B on

Appliance Dimension

Diagram.

Non-Combustible Mantels - Use with Simon Fronts

Non-combustible Mantel and Wall

Projections for use with Demi / Tres

Fronts

FLUSH WITH FIREPLACE OPENING (TOP OF HOOD)

30 in. minimum

to ceiling

6 in.

Figure 10.6 Non-Combustible Mantel Leg or Wall Projections

(Acceptable on both sides of opening)

Non-Combustible Mantel Legs or Wall Projections -
Use with Demi / Tres Fronts

Figure 10.5 Minimum Vertical and Maximum Horizontal

Dimensions for Non-Combustible Mantels

TOP OF

APPLIANCE

DRYWALL

FIREPLACE OPENING

See Dimension B on

Appliance Dimension

Diagram.

6 in.

Non-Combustible Mantels - Use with Demi / Tres

Fronts

* Note:

When using a DEMI or TRES decorative barrier

front a 1/2 in. clearance must be maintained from the

fireplace opening to allow room for decorative barrier

front removal / install.

** Note:

When using a DEMI or TRES decorative

barrier front a 1/4 in. clearance must be maintained on

both sides of the fireplace opening to allow room for

decorative barrier front removal / install.

Содержание NNXT33-IFT




































































Результаты поиска

Содержание NNXT33-IFT

Отзывы:

Heatilator NNXT33-IFT, Руководство по установке, Страница: 50 / 67

Результаты поиска

Содержание NNXT33-IFT

Отзывы: