manualshive.com logo in svg

Heatilator NNXT33-IFT, Руководство по установке, Страница: 2 / 67

Поделиться
Скачать
Heatilator NNXT33-IFT Скачать руководство пользователя страница 2

Heatilator  •  NNXT33-IFT, NNXT33L-IFT, NNXT36-IFT, NNXT36L-IFT Installation Manual  •  2628-980  Rev. C  •  8/20

2

    Safety Alert Key:

•  DANGER! 

Indicates a hazardous situation which, if not avoided 

will

 result in death or serious injury.

•  WARNING! 

Indicates a hazardous situation which, if not avoided 

could

 result in death or serious injury.

•  CAUTION!

 Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

•  NOTICE:

 Used to address practices not related to personal injury.

Note: 

The term “recommend” or “recommended” does not indicate a requirement.  It is a best practice suggested by Hearth 

& Home Technologies

®

.  Failure to perform the recommended task will not result in a safety concern.

Table of Contents

Installation Standard Work Checklist

  . . . . . . . . . . . . . . . . . . . . 3

1 Product Specific and Important Safety Information

  

 

A.  Appliance Certification

  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

B.  Glass Specifications

  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

C.  BTU Specifications

  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

D.  High Altitude Installations  . . . . . . . . . . . . . . . . . . . . . . . . . . 4

E.  Non-Combustible Materials Specification

. . . . . . . . . . . . . . 4

F.  Combustible Materials Specification

  . . . . . . . . . . . . . . . . . 4

G. Electrical Codes  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
H. California   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
I.  Requirements for the Commonwealth of Massachusetts . . 5

2 Getting Started 

A.  Design and Installation Considerations  . . . . . . . . . . . . . . . 6
B.  Good Faith Wall Surface   . . . . . . . . . . . . . . . . . . . . . . . . . . 6
C.  Tools and Supplies Needed  . . . . . . . . . . . . . . . . . . . . . . . . 6
D.  Inspect Appliance and Components . . . . . . . . . . . . . . . . . . 7

3 Framing and Clearances 

 

A.  Appliance/Decorative Front Dimension Diagrams  . . . . . . . 8
B. 

Appliance Location and 

Clearances to Combustibles  . . . 12

C.  Constructing the Appliance Chase  . . . . . . . . . . . . . . . . . . 14

4 Termination Location and Vent Information   

A.  Approved Pipe  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
B.  Vent Termination Minimum Clearances  . . . . . . . . . . . . . . 15
C.  Vent Terminal Clearances  . . . . . . . . . . . . . . . . . . . . . . . . 16
D.  Use of Elbows   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
E.  Vent Diagrams  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

5 Vent Clearances and Framing 

 

A.  Pipe Clearances to Combustibles   . . . . . . . . . . . . . . . . . . 31
B.  Wall Penetration Framing/Firestops  . . . . . . . . . . . . . . . . . 32
C.  Ceiling Firestop/Floor Penetration Framing  . . . . . . . . . . . 33
D.  Install Attic Insulation Shield . . . . . . . . . . . . . . . . . . . . . . . 33

6 Appliance Preparation 

A.  Top Vent  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
B.  Prepare For Heat Management  . . . . . . . . . . . . . . . . . . . . 36
C.  Securing and Leveling the Appliance  . . . . . . . . . . . . . . . . 36

7 Venting and Chimneys 

 

A.  Assemble Vent Sections  (DVP Pipe Only)   . . . . . . . . . . . 37
B.  Assemble Slip Sections  . . . . . . . . . . . . . . . . . . . . . . . . . . 39
C.  Secure the Vent Sections . . . . . . . . . . . . . . . . . . . . . . . . . 39
D.  Disassemble Vent Sections  . . . . . . . . . . . . . . . . . . . . . . . 40
E.  Vertical Termination Requirements . . . . . . . . . . . . . . . . . . 40
F.  Horizontal Termination Requirements   . . . . . . . . . . . . . . . 41
G.  Shrouds  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

8 Electrical Information 

A.  General Information  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
B.  Wiring Requirements  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

9 Gas Information 

A.  Fuel Conversion  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
B.  Gas Pressure  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
C.  Gas Connection  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
D.  High Altitude Installations  . . . . . . . . . . . . . . . . . . . . . . . . . 47
E.  Air Shutter Setting   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

10 Finishing 

A.  Facing Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
B.  Mantel and Wall Projections . . . . . . . . . . . . . . . . . . . . . . . 49
C. Non-combustible Mantel and Wall Projections for use with 

Simon Fronts  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

D. Non-combustible Mantel and Wall Projections for use with 

Demi / Tres Fronts  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

11 Appliance Setup 

A.  Remove the Shipping Materials  . . . . . . . . . . . . . . . . . . . . 51
B.  Clean the Appliance  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
C.  Install Burner Media / Embers  . . . . . . . . . . . . . . . . . . . . . 51
D.  Install Control Heat Shield  . . . . . . . . . . . . . . . . . . . . . . . . 52
E.  Install Fixed Glass Assembly  . . . . . . . . . . . . . . . . . . . . . . 52
F.  Install Decorative Barrier Front. . . . . . . . . . . . . . . . . . . . . 52
G.  Install Logs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

12 Reference Materials 

 

A.  Vent Components Diagrams   . . . . . . . . . . . . . . . . . . . . . . 55
B.  Optional Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
C. Accessories  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

 =  Contains updated information.

Содержание NNXT33-IFT




































































Отзывы:

Нет отзывов