Heatilator ECO-ADV-WS18 Скачать руководство пользователя

Страница: 24 / 46

7056-138L • August 23, 2019

Heatilator EcoChoice WS18

www.heatilatorecochoice.com

Snap Disc

Magnet

Spade

Connectors

Figure 24.1

Disconnect power supply. Locate the snap disc

bracket assembly at the bottom left rear corner of the

appliance

(Figure 24.1)

2. A magnet holds the bracket to the appliance. Pull the

bracket down away from the appliance to expose the

snap disc.

3. Pull the snap disc and spade connectors up and out of

bracket as shown in

Figure 24.2

4. Using a Phillips head screw driver, remove the 2 screws

from the snap disc and then remove the snap disc from

the spade connectors. Replace with new snap disc and

re-connect to spade connectors.

5. Push the snap disc and spade connectors back inside

bracket and re-attach the bracket to the appliance.

Figure 24.2

Snap Disc Location

C. Snap Disc Replacement

Figure 24.3

D. Door Handle Assembly

CAUTION

Do not

over tighten lock nut. The door handle needs to

move smoothly.

Locknut

Door Cross

Section

Latch Cam

3/8 inch

Spacing

Washers

Square Key

Door Handle

Shaft

Spring

Handle

Add up to 3

washers on

this side of

the door

Install washer on door handle shaft.

Slide door handle through door.

3. Add up to three washer as shown in

Figure 24.3

on the

inside of the door.

Install key in groove.

5. Align groove in latch cam with key; slide latch cam

over shaft

Install locknut but do not over tighten, the handle needs

to move smoothly.

Install handle turning in a counter-clockwise motion to

desired location on door handle rod (

Figure 24.3).

Содержание ECO-ADV-WS18















































Результаты поиска

Содержание ECO-ADV-WS18

Отзывы:

Похожие инструкции для ECO-ADV-WS18

Бренды по названию

Популярные бренды

Heatilator ECO-ADV-WS18, Руководство пользователя по установке и эксплуатации

Результаты поиска

Содержание ECO-ADV-WS18

Отзывы:

Похожие инструкции для ECO-ADV-WS18

Бренды по названию

Популярные бренды