manualshive.com logo in svg

Heatilator ECO-ADV-WS18, Руководство пользователя по установке и эксплуатации

Поделиться
Скачать
Heatilator ECO-ADV-WS18 Скачать руководство пользователя страница 25

7056-138L • August 23, 2019

25

Heatilator EcoChoice WS18

www.heatilatorecochoice.com

Figure 25.2

2 pc Baffle Board

Tube Channels

Baffle 

Protection 

Channel

Ceramic Blanket on Top

Burn Rate 

Air Control

Baffle Boards & Blanket 

even with front tube and 

resting on back tube

Figure 25.1 - Baffle 

1. 

Remove all ash from the firebox, and extinguish all hot 

embers before disposal into a metal container.

2. 

Remove the baffle protection channel by rotating it 

down from the front tube

 (Figure 25.2)

.

3. 

The baffle board has 2 pieces. With the ceramic 

blanket still in place, slide one baffle piece over 

the top of other one and pull out top piece through 

the door opening and then remove bottom baffle 

piece

 (Figure 25.1)

.

4.  Remove the ceramic blanket.

5.  Re-install the ceramic blanket and smooth out 

the blanket.

6. 

Slide the baffle pieces one piece at a time underneath 

the blanket.  Be sure the baffle boards are even 

with the front manifold tube and is resting on all 

tubes 

(Figure 25.1 and 25.2)

.

7. 

Re-install the baffle protection channel by rotating it 

up and around the front tube so the bottom flange of 

the channel rests behind the manifold tube. The baffle 

boards and blanket are tucked inside the rear of the 

baffle protection channel.

E. Baffle Removal

Содержание ECO-ADV-WS18















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды