manualshive.com logo in svg

Heatilator ECO-ADV-WS18, Руководство пользователя по установке и эксплуатации

Поделиться
Скачать
Heatilator ECO-ADV-WS18 Скачать руководство пользователя страница 32

7056-138L • August 23, 2019

32

Heatilator EcoChoice WS18

www.heatilatorecochoice.com

NOTE: 

Clearances may only be reduced by means 

approved by the regulatory authority having 

jurisdiction

BACKWALL / SIDEWALL 

A

B

C

D

E

F

E

F

CORNER INSTALLATION

G

H*

90° OFF TOP 

UP & OUT CEILING 

CLEARANCE

STOVE TO CEILING 

CLEARANCE 

C

D

ALCOVE TOP VIEW 

G

A

B

ALCOVE SIDE VIEW

C. Clearances to Combustibles (UL and ULC)

MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS: INCHES & (MILLIMETERS)

NOTE: ALL “A”, “C” AND “F” DIMENSIONS ARE TO INSIDE DIAMETER OF FLUE COLLAR.

A

B

C

D

E

F

G

H

INSTALLATION: Full Vertical OR Horizontal with 2 foot (609mm) minimum vertical Off Appliance Top

Single Wall Pipe

12 (305)

8.25 (210) 21 (533.4) 11.5 (292) 3.5 (89)

13 (330)

54.25 (1378)

*

Double Wall Pipe

10.75 (273)

7 (178)

19 (482.6)

9.5 (241)

3 (76)

12.5 (317.5) 54.25 (1378) 10 (254)

INSTALLATION: 90

°

 Elbow Off Top of Appliance Through Back wall

Single Wall Pipe

11.75 (298)

8 (203)

18.25 (464) 8.5 (216) 3.5 (89)

13 (330)

54.25 (1378)

*

Double Wall Pipe

11.75 (298)

8 (203)

18.25 (464) 8.5 (216)

3 (76)

12.5 (318) 54.25 (1378) 10 (254)

For alcove only: 

Six inch diameter listed Double wall air insulated connector pipe with 

UL103 HT listed factory built 

Class A chimney or masonry chimney

. Maximum depth of Alcove shall be no more than 48 inches (1219mm) and the 

referenced alcove clearances. Canada must comply with 

CAN/ULC-S269 M87 for the 650° factory built chimney

.

* SEE PIPE MANUFACTURERS CLEARANCES - NOT TESTED

Fire Risk.

•  Comply with all minimum clearances to 

combustibles as specified.

• 

Failure to comply may cause house fire.

WARNING

NOTE: Service Space

• 

In order to replace the tube channel assembly a 

clearance of 19 inches (483mm) is required on the 

right side of appliance in order to remove the tubes 

with the appliance in place.

• 

If space is not available, the appliance will have to be 

disconnected from the chimney to proceed with the 

tube replacement.

Содержание ECO-ADV-WS18















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды