manualshive.com logo in svg

Heatilator ECO-ADV-WS18, Руководство пользователя по установке и эксплуатации

Поделиться
Скачать
Heatilator ECO-ADV-WS18 Скачать руководство пользователя страница 4

7056-138L • August 23, 2019

4

Heatilator EcoChoice WS18

www.heatilatorecochoice.com

B. Warranty Policy

Page 1 of 2

June 6, 2019

7014-212C

Hearth & Home Technologies Inc.

HEATILATOR ECO-CHOICE WARRANTY

Hearth & Home Technologies Inc., on behalf of its hearth brands (“HHT”), extends the following warranty for ECOCHOICE 

by Heatilator wood and pellet hearth appliances that are purchased from an HHT authorized dealer.

WARRANTY COVERAGE:

HHT warrants to the original owner of the HHT appliance at the site of installation, and to any transferee taking 

ownership of the appliance at the site of installation within two years following the date of original purchase, that the HHT 

appliance will be free from defects in materials and workmanship at the time of manufacture.  After installation, if covered 

components manufactured by HHT are found to be defective in materials or workmanship during the applicable warranty 

period, HHT will, at its option, repair or replace the covered components.  HHT, at its own discretion, may fully discharge 

all its obligations under such warranties by replacing the product itself or refunding the verifi ed purchase price of the 

product itself.  The maximum amount recoverable under this warranty is limited to the purchaser price of the product.  This 

warranty is subject to conditions, exclusions and limitations as described below.

WARRANTY PERIOD:

Warranty coverage begins on the date of original purchase.  In the case of new home construction, warranty coverage 

begins on the date of fi rst occupancy of the dwelling or six months after the sale of the product by an independent, 

authorized HHT dealer/distributor, whichever occurs earlier.  The warranty shall commence no later than 24 months 

following the date of product shipment from HHT, regardless of the installation or occupancy date.  The warranty period 

for parts and labor for covered components is produced in the following table.

Warranty Period

Heatilator ECO-CHOICE  

Appliances

Components Covered

Parts

Labor

Pellet

EPA Wood

1 year

X

X

All parts and material except as covered by 

Conditions, Exclusions, and Limitations Listed

3 years

X

Firepots and burnpots

3 years

1 year

X

X

Castings

5 years

3 years

X

Manifold tubes

5 years

3 years

X

X

Firebox and heat exchanger

90 days

X

X

All replacement parts beyond warranty period

See conditions, exclusions, and limitations on next page

Содержание ECO-ADV-WS18















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды