manualshive.com logo in svg

Heatilator ECO-ADV-WS18, Руководство пользователя по установке и эксплуатации

Поделиться
Скачать
Heatilator ECO-ADV-WS18 Скачать руководство пользователя страница 39

7056-138L • August 23, 2019

39

Heatilator EcoChoice WS18

www.heatilatorecochoice.com

1. 

Align holes in mounting flange of blower with bolt holes 

in appliance. Blower should be positioned at bottom of 

rear outer skin as shown in 

Figure 39.1

.

2. 

Insert and tighten bolts supplied with the kit, securing 

blower onto outer wall of appliance.

3.  Place the bracket containing the snap disc and 

magnet under the bottom left rear corner as shown 

in 

Figure 39.1

.

See 

pages 14 and 21

 for detailed operating instructions for 

the blower and snap disc.

Figure 39.1

The blower speed control for this appliance is 

adjusted at the factory, and normally does not require 

further adjustment.

NOTE:

 When the speed control is turned clockwise, it 

will click on to high speed. Continue to turn the 

speed control clockwise to decrease the speed.  

At full clockwise, the blower should blow gently, 

but should not stop.

MANUAL: Over-rides the 

Snap Disc

AUTO:  Fan will turn ON/OFF 

Automatically by the Snap Disc

Controls the Fan Speed

Snap Disc Bracket 

with Magnet

Blower

Snap Disc

B. Blower Installation (Optional)

C. Adjusting the Blower Speed Control

Shock Risk

.

• 

Do NOT remove grounding prong from 

plug.

•  Route cord away from appliance.

• 

Do NOT route cord under or in front 

of appliance.

•  Plug directly into properly grounded 3 

prong receptacle.

CAUTION

Содержание ECO-ADV-WS18















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды