Heatilator ECO-ADV-WS18 Скачать руководство пользователя

Страница: 26 / 46

7056-138L • August 23, 2019

Heatilator EcoChoice WS18

www.heatilatorecochoice.com

Figure 26.1

Side Panel

Tube

Channel

Assembly

Tube Channel Rack

Channel Bolts (3)

Channel Access

Cover

Remove 3

Screws

Channel

Cover

Screws (4)

Removing Tube Channel Assembly

Remove the baffle protection channel, ceramic blanket

and the 2 baffle boards. See instructions on page 25.

2. Remove the right side shield by removing 3 screws in

the back using a Phillips head screw driver.

3. Remove 4 screws from channel access cover and

remove cover.

Locate 3 channel bolts behind the channel access

cover and remove using a 7/16 socket wrench. Slide

out tube channel assembly.

F. Tube Channel Assembly Replacement

NOTE:

Soak the bolts with penetrating oil for at least 15

minutes before trying to remove them.

Replacing Tube Channel Assembly

Slide the tube channel assembly into side of firebox

and insert each tube into the corresponding hole in the

tube channel rack starting with the back hole first.

Make sure tube channel assembly is flush against the

side of the appliance and secure with channel bolts.

7. Re-install channel cover and side shield.

Re-install ceramic blanket, baffle pieces and baffle

protection channel

(See instructions of page 25)

NOTE: Service Space

In order to replace the tube channel assembly a

clearance of 19 inches (483mm) is required on the right

side of appliance in order to remove the tubes with the

appliance in place.

If space is not available, the appliance will have to be

disconnected from the chimney to proceed with the

tube replacement.

Содержание ECO-ADV-WS18















































Результаты поиска

Содержание ECO-ADV-WS18

Отзывы:

Похожие инструкции для ECO-ADV-WS18

Бренды по названию

Популярные бренды

Heatilator ECO-ADV-WS18, Руководство пользователя по установке и эксплуатации

Результаты поиска

Содержание ECO-ADV-WS18

Отзывы:

Похожие инструкции для ECO-ADV-WS18

Бренды по названию

Популярные бренды