manualshive.com logo in svg

Heat & Glo PRIMO48, Руководство по установке, Страница: 70 / 88

Поделиться
Скачать
Heat & Glo PRIMO48 Скачать руководство пользователя страница 70

70

Heat & Glo  •  PRIMO48, PRIMO48ST, PRIMO60, PRIMO60ST, PRIMO72, PRIMO72ST Installation Manual  •  2310-970 Rev. L  •  2/16  

Figure 10.29  Bottom Granite Piece Installed

4.  Slide both side granite pieces outward as shown in 

Figure 10.29.  Verify dimensions in Figure 10.25, 10.27 
and 10.29.

5.  Place plastic washers as shown in Figure 10.29.  The 

washers serve as spacers for granite placement. If 
washers are not used, the side granite will be dif

fi

 cult 

to remove.

6.  Apply a generous amount of adhesive to the back side 

of the bottom granite piece. The same method will be 
used for top and bottom pieces.  See Figure 10.28 for  
appropriate zone to apply adhesive.  DO  NOT  apply 
adhesive too close to the edges. Leave 1 in. around 
edges.   Avoid leakage of adhesive around edges by not 
applying it too close to the edge of the granite.  Place 

X

MODEL

X

PRIMO48

58 IN.

PRIMO60

70 IN.

PRIMO72

82 IN.

Figure 10.28.  Apply Adhesive For Top and Bottom Granite

1 IN.

1 IN.

1 IN.

1 IN.

APPLY ADHESIVE

EDGE IS 
FLUSH

BRACE TO SUPPORT WEIGHT

NOTICE!  

Verify the left and right side granite is correctly 

installed per Figure 10.25, 10.27 and 10.29.

7.  Align the top edge with the bottom of the left and right 

outside pieces so the edges of the bottom piece are 

fl

 ush with the side pieces. See Figure 10.29.  Secure 

the bottom granite in place with clamps or braces.  
See Figure 10.29.  Do not remove supports or operate 

fi

 replace for 24 hours.    

8.  Apply a generous amount of adhesive to the back 

side of the top granite piece.  See Figure 10.28. The 
granite material is heavy and will need to be adequately 
secured to the wall.  

PLASTIC WASHERS

the bottom piece and hold with braces and clamps to 
support granite.

Содержание PRIMO48

























































































Отзывы:

Нет отзывов