Heat & Glo PRIMO48 Скачать руководство пользователя страница 52

Страница: 52 / 88

Heat & Glo • PRIMO48, PRIMO48ST, PRIMO60, PRIMO60ST, PRIMO72, PRIMO72ST Installation Manual • 2310-970 Rev. L • 2/16

3. Remove the transition media from the appliance. Lift

the transition media tray out of appliance. Disconnect
the reset switch. The transition media tray

ts tightly,

lift carefully.

4. Loosen two shoulder bolts from the transition LED

tray assembly located below the appliance opening.
Carefully remove the transition LED tray assembly.

NOTICE:

LED wires are installed. Handle transition LED

tray assembly with care.

5. Turn off power to the module and valve by unplugging

the 6V transformer from the junction box.

6. Turn off gas valve. The red shutoff knob is located on

the supply line. Turn ball valve off.

If additional access is needed, proceed as follows:

7. Remove

rebox glass from appliance by unlatching

the top spring latches from the glass frame and lifting
glass frame assembly out of the bottom bracket. See
Section 11.

8. Remove interior media, logs, and panels from the unit

if already installed.

9. Remove the burner glass. See Figure 9.3.
10. Remove the media tray. It is attached to the interior

rebox bottom with screws. See Figure 9.3.

11. Remove the two screws that attach the pilot to the

burner leg.

12. Remove the six screws securing the burner to the

re-

box sides and disengage burner from ori

ce. Remove

burner. See Figure 9.4.

13. Remove the screws that secure the glass window.

Remove the glass window. Handle with care. See
Figure 9.5.

14.

Carefully remove LED tray assembly from appliance by
lifting up and out through the bottom glass opening.

NOTICE:

LED wires are installed. Handle transition LED

tray assembly with care.

C. Gas Service Access

LOWER ACCESS COVER PANEL

TRANSITION MEDIA TRAY

ELECTRICAL ACCESS PLATE

Figure 9.2. Gas Service Access

IMPORTANT NOTE:

The lower access cover panel is re-

movable if

nishing materials are not installed. See Figure

9.2. If

nishing materials are installed, lift the transition

media tray out of glass frame bracket to access valve cav-
ity.

CAUTION! Risk of Cuts!

Wear protective gloves and

safety glasses during installation. Use suction cups to
handle safety barrier glass.

Note:

If a granite surround is installed, the two side sec-

tions need to be removed in order to access the gas train.
See Section 10.C.
1. Remove the safety barrier glass with two suction

cups. Lift the glass up and out of the opening. See
Section 11 for instructions.

2. Remove side glass or granite transition panels and

remove the granite and/or glass transition brackets
located on the left and right sides of the appliance
opening. See Section 10 for details.

GAS ACCESS PLATE

NOTE: GAS ACCESS PLATE MUST
REMAIN INSTALLED

LOWER ACCESS COVER PANEL

Содержание PRIMO48

























































































Результаты поиска

Содержание PRIMO48

Отзывы:

Heat & Glo PRIMO48, Руководство по установке, Страница: 52 / 88

Результаты поиска

Содержание PRIMO48

Отзывы: