Heat & Glo PRIMO48 Скачать руководство пользователя страница 55

Страница: 55 / 88

Heat & Glo • PRIMO48, PRIMO48ST, PRIMO60, PRIMO60ST, PRIMO72, PRIMO72ST Installation Manual • 2310-970 Rev. L • 2/16

E. High Altitude Installations

NOTICE:

If the heating value of the gas has been reduced,

these rules do not apply. Check with your local gas utility
or authorities having jurisdiction.

When installing above 2000 feet elevation:
• In the USA: Reduce burner ori

ce 4% for each 1000 feet

above 2000 feet.

• In CANADA: Reduce burner ori

ce 10% for elevations

between 2000 feet and 4500 feet. Above 4500 feet,
consult local gas utility.

Figure 9.9 Air Shutter Location

F. Air Shutter Setting

Air shutter settings may be adjusted by a quali

ed installer

at the time of installation. The air shutter is set at the fac-
tory for optimal

ame appearance. The factory air shutter

setting is recommended for all vent runs. See Figure 9.9.
• Refer to Gas Service Access instructions in Section 9.C

to access the air shutter.

•  Loosen the 1/4 in. screw.
•  Twist shutter to adjust.
•  The factory setting is recommended for all vent runs.
•  Do not close the air shutter more than 1/16 in. for NG or

3/8 in. for propane.

• Tighten the screw.

NOTICE:

If sooting occurs, provide more air by opening

the air shutter.

Air Shutter Settings

PRIMO48

PRIMO48ST

Propane

1/16 in.

3/8 in.

PRIMO60

PRIMO60ST

1/8 in.

Full Open

PRIMO72

PRIMO72ST

1/8 in.

N/A

DETAIL

The PRIMO is equipped with an
internal air shutter.

Содержание PRIMO48

























































































Результаты поиска

Содержание PRIMO48

Отзывы:

Heat & Glo PRIMO48, Руководство по установке, Страница: 55 / 88

Результаты поиска

Содержание PRIMO48

Отзывы: