manualshive.com logo in svg

Heat & Glo PRIMO48, Руководство по установке, Страница: 32 / 88

Поделиться
Скачать
Heat & Glo PRIMO48 Скачать руководство пользователя страница 32

32

Heat & Glo  •  PRIMO48, PRIMO48ST, PRIMO60, PRIMO60ST, PRIMO72, PRIMO72ST Installation Manual  •  2310-970 Rev. L  •  2/16  

Electrical Connections

Wire 110-120 VAC service  from the appliance to the  junc-
tion box.   See Figure 6.13. Use wire nuts to secure the 
110-120VAC service wires to the hot and neutral fan wires 
and screw  the 110-120 VAC ground wire to the fan box. 
See Wiring Diagram in section 8 of the appliance manual.
Screw the duct cover to the fan box.
Screw the register adapter frame and the air register to 
the fan housing.
Complete the 

fi

 replace installation per instructions.

Other Duct Options

Metal Oval Air Duct

: Attach the round-to-oval adapter to 

the HEAT-ZONE-PRIMO collar with screws.  Attach the 6" 
oval duct to the adapter with screws. Complete the duct 
run and attach the oval duct to the fan housing. 

Note

: 6 

in. metal oval duct is NOT provided with the HEAT-ZONE-
PRIMO kit, but can be purchased from an HVAC supplier.

Metal Round And Oval Duct

: A combination of 6 in. 

round and 6 in. oval air duct can be used in the duct run. 
Metal duct components may be purchased from an HVAC 
supplier.

Note:

  Support duct at intervals of no greater than four 

feet, with no more than 1/2 in. sag between supports as 
required by local code. 

 

Tape all seams with aluminum tape 

(1-1/4 in. minimum width, or as speci

fi

 ed by local codes).

Fan Housing

Round to Oval Adapter

6 in. Round Air Duct

Gear Clamp

Screws

Gear Clamp

Mounting Bracket
(Both Sides)

Figure 6.12

CAUTION! Risk of Overheating! 

Tape seams to prevent 

overheating and shut down of appliance. 

Figure 6.13

Plan the location of the 

fi

 replace and the warm air duct run(s).

JUNCTION BOX

JUNCTION BOX

FAN HOUSING

FAN HOUSING

NOTICE: 

This appliance must be electrically wired 

and grounded in accordance with local codes or, in the 
absence of local codes, with 

National Electric Code ANSI/

NFPA 70-latest edition

 or the 

Canadian Electric Code 

CSA C22.1.

Maintenance

Service and maintain the gas 

fi

 replace per instructions.

Keep the air register(s) clean and free of any blockage. 

Содержание PRIMO48

























































































Отзывы:

Нет отзывов