manualshive.com logo in svg

Heat & Glo PRIMO48, Руководство по установке, Страница: 2 / 88

Поделиться
Скачать
Heat & Glo PRIMO48 Скачать руководство пользователя страница 2

2

Heat & Glo  •  PRIMO48, PRIMO48ST, PRIMO60, PRIMO60ST, PRIMO72, PRIMO72ST Installation Manual  •  2310-970 Rev. L  •  2/16  

    Safety Alert Key:

• DANGER! 

Indicates a hazardous situation which, if not avoided will result in death or serious injury.

• WARNING! 

Indicates a hazardous situation which, if not avoided could result in death or serious injury.

• CAUTION!

 Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

• NOTICE:

 Used to address practices not related to personal injury.

Table of Contents

Installation Standard Work Checklist . . . . . . . . . . . . . . . . . . . . 3

1 Product Speci

fi

 c and Important Safety Information  

A. Appliance Certi

fi

 cation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

B. Glass Speci

fi

 cations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

C. BTU Speci

fi

 cations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

D.  High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . . 4
E.  Non-Combustible Materials Speci

fi

 cation. . . . . . . . . . . . . . 5

F.  Combustible Materials Speci

fi

 cation  . . . . . . . . . . . . . . . . . 5

G. Electrical Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
H.  Requirements for the Commonwealth of Massachusetts . . 6

2 Getting Started 

A.  Design and Installation Considerations . . . . . . . . . . . . . . . 7
B.  Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . . . . . 7
C.  Inspect Appliance and Components . . . . . . . . . . . . . . . . . . 7

3 Framing and Clearances 

 

A.  Appliance/Decorative Finish Dimension Diagrams  . . . . . . 8
B.  Clearances to Combustibles  . . . . . . . . . . . . . . . . . . . . . . 12
C.  Constructing the Appliance Chase . . . . . . . . . . . . . . . . . . 17
D.  Floor Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4 Termination Location and Vent Information   

A.  Vent Termination Minimum Clearances PVI-SLP . . . . . . . 18
B.  Chimney Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
C.  Approved Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
D.  Use of Elbows  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
E.  Measuring Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
F.  Vent System and Diagrams . . . . . . . . . . . . . . . . . . . . . . . 20
G.  Power Vent Baf

fl

 e Adjustment . . . . . . . . . . . . . . . . . . . . . 22

5 Vent Clearances and Framing 

 

A.  Pipe Clearances to Combustibles  . . . . . . . . . . . . . . . . . . 23
B.  Wall Penetration Framing/Firestops . . . . . . . . . . . . . . . . . 24
C.  Ceiling Firestop/Floor Penetration Framing . . . . . . . . . . . 25
D.  Install Attic Insulation Shield . . . . . . . . . . . . . . . . . . . . . . . 25

6 Appliance Preparation 

A.  Vent Collar Preparation  . . . . . . . . . . . . . . . . . . . . . . . . . . 26
B.  Securing and Leveling the Appliance . . . . . . . . . . . . . . . . 27
C.  HEAT-ZONE-PRIMO  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
D.  HEAT-OUT-PRIMO  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
E.  Power Vent Termination Clearances   . . . . . . . . . . . . . . . 37
F.  Burner Glass Installation  . . . . . . . . . . . . . . . . . . . . . . . . . 38

7 Venting and Chimneys 

 

A.  Assemble Vent Sections  . . . . . . . . . . . . . . . . . . . . . . . . . 39
B.  Assemble Slip Sections . . . . . . . . . . . . . . . . . . . . . . . . . . 41
C.  Secure the Vent Sections . . . . . . . . . . . . . . . . . . . . . . . . . 41
D.  Disassemble Vent Sections . . . . . . . . . . . . . . . . . . . . . . . 42
E.  Vertical Termination Requirements (PVI-SLP) . . . . . . . . . 43
F.  Horizontal Termination Requirements Heat 
 

Shield Requirements for Horizontal Termination

 

(PVI-SLP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

8 Electrical Information 

A.  General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
B.  Wiring Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

9 Gas Information 

A.  Fuel Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
B.  Gas Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
C.  Gas Service Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
D.  Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
E.  High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . 55
F.  Air Shutter Setting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

10 Finishing 

A.  Facing and Finishing - General Information . . . . . . . . . . . 56
B.  Clean Face Finish (Black Glass Interior) . . . . . . . . . . . . . 58
C.  Black Granite Surround Finish (Black Granite Interior)  . . 66
D.  Mantel and Wall Projections  . . . . . . . . . . . . . . . . . . . . . . 75

11 Appliance Setup 

A.  Remove the Shipping Materials . . . . . . . . . . . . . . . . . . . . 76
B.  Clean the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
C.  Install Burner Glass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
D.  Install Modern Log Set  . . . . . . . . . . . . . . . . . . . . . . . . . . 76
E.  Install Media   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
F.  Barrier Glass  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
G.  Firebox Glass Assembly  . . . . . . . . . . . . . . . . . . . . . . . . . 78

12 Reference Materials 

 

A.  Vent Components Diagrams  . . . . . . . . . . . . . . . . . . . . . . 79
B.  Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

 =  Contains updated information.

Содержание PRIMO48

























































































Отзывы:

Нет отзывов