manualshive.com logo in svg

Heat & Glo PRIMO48, Руководство по установке, Страница: 3 / 88

Поделиться
Скачать
Heat & Glo PRIMO48 Скачать руководство пользователя страница 3

3

Heat & Glo  •  PRIMO48, PRIMO48ST, PRIMO60, PRIMO60ST, PRIMO72, PRIMO72ST Installation Manual  •  2310-970 Rev. L  •  2/16 

Installation Standard Work Checklist

Appliance Install  Sections 3 , 6 and 11 

        YES  IF NO, WHY?

Veri

¿

 ed that the chase is insulated and sealed. (Pg. 17) 

 

___________________________

Veri

¿

 ed clearances to combustibles. (Pg. 12) 

 

___________________________

Fireplace is leveled and secured. (Pg. 27) 

 

___________________________

Barrier glass installed correctly. “THIS SIDE OUT” is readable.  (Section 11)                      ___________________________

                                                                                                                                         

Venting/Chimney/PowerFlow™ Heat Management  Sections 4,5 and 7

Venting con

¿

 guration complies to vent diagrams. (Section 4) 

 

___________________________

Venting installed, locked, secured in place and sealed with correct clearance.     

___________________________

Firestops installed. (Section 5) 

 

___________________________

Attic insulation shield installed. (Section 5) 

 

___________________________

Exterior wall/Roof 

À

 ashing installed and sealed.  (Section 7) 

 

___________________________

Terminations installed and sealed. (Section 7) 

 

___________________________

PVI-SLP or PVLP-SLP power vent installed with correct baf

À

 e setting. 

 

___________________________

HEAT-ZONE-PRIMO and/or HEAT-OUT-PRIMO installed and vented 

  properly; complies with vent run min./max. requirements in installation manual.                ___________________________

Electrical  Section 8 (Pg 46-50)

Unswitched power (110-120 VAC) provided to the appliance.

 

 

___________________________

LED switch wires properly installed. 

 

___________________________

If only HEAT-OUT-PRIMO is installed: Wall switch plate and toggle switch not installed.             ___________________________

Gas  Section 9 (Pg 51-55)

Proper appliance for fuel type.  

 

___________________________

Was a conversion performed?  

 

___________________________

Leak check performed and inlet pressure veri

¿

 ed.  

 

___________________________

Veri

¿

 ed proper air shutter setting for installation type.  

 

___________________________

Verify that the gas access plate remains installed. (Pg 54)                                               ___________________________

Finishing  Section 10 (Pg 56-75)

1/2 inch sheetrock used as recommended.                                                                       ___________________________

Veri

¿

 ed all clearances meet installation manual requirements. 

 

___________________________

Mantels and wall projections comply with installation manual requirements.  

___________________________

Granite or Clean Face 

¿

 nishing complete and complies with clearance 

     requirements in installation manual.                                                                             ___________________________

Barrier glass properly installed.                                                                                         ___________________________

Appliance Setup  Section 11 (Pg 76-78)

All packaging and protective materials removed (inside & outside of appliance).   

___________________________

Glass or granite panels and media installed correctly. 

 

___________________________

Firebox glass assembly installed and secured. 

 

___________________________

Accessories installed properly.  

 

___________________________

Manual bag and all of its contents are removed from inside/under 

     the appliance and given to party responsible for use and operation. 

   

         ___________________________

Started appliance and veri

¿

 ed no

 

gas leaks exist. 

 

  

    

         ___________________________

Multicolored LED lights work in all switched positions. 

                                                ___________________________

Customer:          
Lot/Address:

Model (circle one):   PRIMO48       PRIMO60    PRIMO72
                                   PRIMO48ST  PRIMO60ST  PRIMO72ST

Date Installed:          
Location of Fireplace:
Installer:
Dealer/Distributor Phone # 
Serial #:

Comments:

 Further description of the issues, who is responsible (Installer/ Builder/ Other Trades, etc) and corrective 

action needed _____________________________________________________________________________________
_________________________________________________________________________________________________

Comments Communicated to party responsible ____________________ by ______________________on ___________   
 

  

                                                  (Builder / Gen. Contractor/)   (Installer) 

                            (Date) 

2310-972 Rev. C  2/16

Î

 =  Contains updated information.

Hearth & Home Technologies recommends the following:

•  Photographing the installation and copying this checklist for your 

¿

 le.  

•  That this checklist remain visible at all times on the appliance until the installation is complete. 

This standard work checklist is to be used by the installer in conjunction with, not instead of, the instructions contained in this 
installation manual.

WARNING! Risk of Fire or Explosion! 

Failure to install appliance according to these instructions can 

lead to a 

¿

 re or explosion.

ATTENTION INSTALLER:

Follow this Standard Work Checklist

Содержание PRIMO48

























































































Отзывы:

Нет отзывов