manualshive.com logo in svg

Hayward OmniPL HLBPLUS4W, Руководство по установке, Страница: 59 / 64

Поделиться
Скачать
Hayward OmniPL HLBPLUS4W Скачать руководство пользователя страница 59

Freeze Protect - 

Select whether you want the accessory to turn on for Freeze 

Protection.  Also set the Freeze Protect air temperature threshold from this 

menu.

Relay - 

Select the relay that the accessory is wired to.  This option only appears 

if the accessory does not have an associated pump configured.

Delete an Accessory -

 

From this screen, if you wish to delete an accessory that is 

currently configured, select the trash can on the right of the name of the accessory 

that you wish to delete.

If Other Options is selected:

Name - 

This is where you will be allowed to rename the Body of Water that you are 

currently configuring to whatever name you desire.

If Backyard is selected:

Select the Equipment that you would like to configure - 

The options are Add Standalone Light 

and Add Accessory. The configuration for these are described in the Configuration Wizard portion of 

this manual. 

If Standalone Light is selected:

Add Standalone Light - 

Pressing “Add Standalone Light” from this screen will take you 

through the full configuration for adding new lights.  These steps are described in the 

Configuration Wizard portion of this manual.

Select an Existing Group of Lights - 

Once you select a group of existing lights, all of 

the options for those lights will appear on the next screen.  These options are as follows:

Name - 

Rename the group of lights to whatever name is desired.

Type - 

Select the type of lights configured.

Relay - 

Select the relay(s) that the group of lights is wired to.

Set Mode - 

Set the mode of the lights configured.

Omni Direct

 - If UCL was previously selected, this button will appear and allow you 

to test whether your UCL lights are Omni Direct compatible (lights built after June 

2018).

Delete an Existing Group of Lights -

 From this screen, if you wish to delete a group of 

lights that is currently configured, select the group and then select the trash can button 

next to it. 

If Accessories is selected:

Add Accessory - 

Pressing “Add Accessory” from this screen will take you through the 

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

56

Содержание OmniPL HLBPLUS4W

































































Отзывы:

Нет отзывов