background image

- 7 -

V3-10-10

 Assembly instructions terrace awning TR850

Then take firm hold of the horizontal rails by the end with the corner 
piece and bring this section immediately above the vertical bases. Now 
press the corner piece into the vertical guide rail (Fig. 14). The guide rails 
will now stand up by themselves.
Then remove the long intermediate rollers from the packaging. (N.B.: 
there are two different sizes. There will always be a marked roller which 
is 3 mm shorter than the others. This roller is fitted last, in the middle of 
the corner).
Now fit intermediate rollers Nos. 1 and 2  on the drawing (fig. 15). The 
fitting of these tubes must be carried out using a M10 x 20 screw for the 
outer screws and M10 x 30 for the screws on the inside, which also pull 
the corner piece tight.

Make sure that the upper edge of the tube is always level with the upper 
edge of the guide rails. (The centre line of the tube may be out of align-
ment).

Then position the central roller on the corner with two M10 x 20 screws 
at each end. If the tubes are fitted in the wrong order there may be dif-
ficulty tightening the bolts with a spanner. 
If one or more intermediate rollers are to be fitted in the sloping part of 
the guide rail, these are now dealt with. The spacing between these must 
be kept even, and the position of the rollers must be identical at left and 
right. Now take a spirit level and a ruler and position the base supports 
perfectly vertical and at their correct distance from each other.

The distance between the two parallel base supports must match the 
measurement at the top of the casing precise to the millimetre.
Re-check the squareness of the guide rails with respect to the wall.

If the differences in level were given when ordering the sunblind, the 
tubes in the corner should now automatically be perfectly level. If a variation should, however, have 
com about through a lack of precision in the measurements, this can be corrected by placing som pack-
ing material beneath the base supports.
This alignment of the guide rails is abso-
lutely necessary to avoid later problems 
rolling up the long drops of fabric. Then 
draw the drill holes on the floor (foun-
dations) through the holes in the base 
supports, and screw the base supports 
firm. Lay the remainder of the cable in the 
outermost groove, in the middle of the pul-
leys in the corner piece (fig. 16).

Then pass the cable through below the 
large wheel of the runner (fig 17-1) and 
turn it through 180 degrees (2). Now insert 
the end into the drop bar behind the small 
wheel (3). Use a thread if necessary to help pull the cable through under the wheel of the runner.
Make a careful check that the cable is running properly on all the pulleys.

fig. 15

fig. 17

fig. 16

Содержание TR850

















Отзывы: