background image

- 2 -

V3-10-10

 Assembly instructions terrace awning TR850

Contents

A. 

Introduction   

 

 

 

             

 

 

page 2

B. 

General warnings ! 

 

 

 

             

 

 

page 2

C. 

List of tools required 

 

 

 

 

 

 

page 2

D. 

Fitting instructions 

 

 

 

 

 

 

page 3

E. 

Electrical conne motor 

 

             

 

 

 

page 10

F. 

Finishing and maintenance 

 

 

 

 

 

page 13

Trouble-shooting 

 

 

 

             

 

 

page 15

A. Introduction

The Harol TR850 terrace awning is an outside sun protection to be fitted on your  terrace. This sun 
protection blocks the sun rays and thereby protects your terrace against overheating.
These assembly instructions explain step by step the fitting of this system. 

B. General warnings !

For a safe fitting, use and maintenance of this sun protection a number of precautions have to be 
taken. For the safety of everyone concerned, please do take notice of the following general warnings !
-  This manual is meant to be used by professionals only! It is not to be used bij DIY-enthusiasts or 

apprentice fitters.

- Before you start ,please do read these instructions thoroughly.
-  The tightening of springs creates important powers. Be very careful and make sure of a solid footing 

whilst operating.

-  Provide sufficent light in the fitting area. Dispose of obtsacles and dirt. Make sure that, except for 

the fitters, no other people are in the fitting area. Unauthorized people might be in the way or at risk 
themselves.

-  Whilst operating the system, you must be able to overlook the complete area and the whole of the 

sun protection. There are a number of places where people might get injured. Especially watch the 
following parts where people might risk to get jammed : the extension profile, the bench, the guide 
rails and the casing.

C. List of tools required

ladder(s)

electric drill

masonry drills, 6 and 16 mm

spanner, 19mm

water hose or spirit level

measuring rod 

chalk or felt pen

cross-head and flat-head screwdrivers

socket wrenches, 2,5 + 3 mm

flat spanner 7 mm for cable clips

hoist to set up cable and springs

voltmeter or testing lamp 220V

test cable to connect awning

Содержание TR850

















Отзывы: