manualshive.com logo in svg
background image

3 | 

P a g e

TABLE OF CONTENTS

Warranty Information

Harmar, warrants to the “original purchaser” a three-year limited warranty for any Elevation Ramps 

modular ramping and its components that are deemed “warranted” by the original manufacturer. If modular

ramp and its components are not deemed “warranted” the the original manufacturer then Hamrar will in turn

not warranty any cost for service, repair or replacement with said parts. 

Harmar only warraties to the “original purchaser” for said Elevation Ramps modular ramping and its components

supplied by Harmar. This warranty is non-transferrable and in no event will Harmar be responsible for any direct

or indirect damages to the modular ramp and its components. Harmar will not warrant damages to the Elevation 

Ramps modular ramping and its components due to the direct or indirect violation of the 850 lb weight limit or

safety measurements stamped on said Elevation Ramps modular ramping and its components. 

Harmar does not warrant any damage or failure of the modular ramp and its components caused by misuse, 

abuse, accidents, physical damage or modifications or replairs made by anyone other than Harmar Authorized

Dealers or an Elevation Ramps authorized representative.  

Product Specifications 

Before You Start 

Installation Flowchart 

Recommended Tools 

Platform Assembly 

Mounting The J-Hook 

Ramp Run Assembly 

10-11

Ramp Run Handrail Assembly 

12 

End Loop Handrail Assembly 

13 

Platform Handrail Assembly 

14-15

Final Inspection 

16 

04OCT19  | 630-00103-01 Rev B

Содержание MODRAMP

















Отзывы: