Harman Kardon DVD 48, Руководство пользователя

Страница: 24 / 56

24 24
INITIAL SETUP
Before you begin enjoying your new DVD player, a few adjustments
should be made to configure it.
Make sure that you have connected a video display to one of the video
monitor outputs. When you turn on your display and the DVD 48, you
should see the DVD 48’s splash screen. The DVD 48 will determine whether
a disc is loaded and, if so, begin play. If not, the splash screen will remain.
IMPORTANT NOTE: The DVD 48 is not capable of outputting
both HDMI and component video signals simultaneously. If you
have used either of these connections and have no picture, the
likely problem is that the DVD 48 is set to output only the other
type of video.
This is easily fixed by pressing the HDMI Button on the remote
to turn the HDMI Output On or Off as desired. This command
will have the opposite effect on the Component Video Outputs.
In addition, if you are using the Component Video Outputs and
have no picture or a very distorted picture, check whether your
display is capable of receiving a progressive-scan video signal.
If it is not, temporarily use a composite video connection to the
display so that you can view the Setup menus. Press the Setup
Button and use the
⁄
/
¤
Buttons to select the Video tab.
Press the Enter Button, and use the
⁄
/
¤
Buttons again to
select the Progressive Scan setting. Use the
⁄
/
¤
Buttons
to change it from On to Off. If you select the video display’s
component video inputs, you should have no trouble viewing
the picture.
Alternatively, you may reset the setting to the default Interlaced
Scan without using a composite video connection to view the
on-screen menus by following these steps:
1. Press the Open/Close Button on the front panel to open
the disc drawer.
2. Press the Clear Button on the remote control.
3. Enter the numeric code “1211” on the remote.
4. Press the Audio Button (not Audio Mode).
As a last resort, you may perform a system reset that will
require you to reenter all user settings. Press and hold the Clear
Button on the remote for 5 seconds. The display will blink, and
all user settings will return to their factory defaults.
Using the On-Screen Menu System
The DVD 48 uses two types of menu screens: Setup Menus and
Status Displays.
Press the Setup Menu Button on the remote to display the SYSTEM
SETUP menu. See Figures 19 and 20.
Figure 19 – Setup and Navigation Buttons
Figure 20 – System Setup Menu Screen
All of the DVD 48’s menu screens follow the same basic format.
Select a menu by highlighting its tab on the left side of the screen. The
menu’s settings will be previewed, but you will not be able to make any
changes. See Figure 20. Press the Enter Button to make adjustments to
the menu. The tabs will disappear, and the menu will shift to a grid view,
displaying the setting name in the left column and allowing you to select
a value in the right column. See Figure 21.
Figure 21 – General Setup Menu
As shown in Figure 21, the first setting in the menu will automatically
be selected. It will be displayed in a different color with arrows on either
side. If you wish to change its value, use the
‹
/
›
Buttons to scroll
through the available settings. Some settings changes, especially those
pertaining to video, may cause the screen to go dark momentarily as
the DVD 48 reconfigures itself. When the desired setting is displayed,
use the
⁄
/
¤
Buttons to select another setting. If the menu has two
pages, indicated in the upper right corner by the second number,
simply continue to scroll down the list of settings, and the DVD 48
will automatically skip to the second page as appropriate.
Some settings display only a right arrow in place of a value. This indi-
cates that the setting leads to a submenu containing additional settings.
Press the
›
or Enter Button to display the submenu.
Other settings call for numeric entries, such as the password to access
the Parental Rating setting and the password to reset the system to its