52
PROGRAMMING THE REMOTE
Programming the Remote
the
DEVICE IN USE
on the left side of the bot-
tom line and the
PUNCH-THROUGH
device. In
the example used, the display to return the
remote to default settings will appear as shown
in Figure 58.
Figure 58
Transport Punch-Through
Transport punch-through allows the
Play
P
,
Stop
P
,
Fast Forward/Reverse
P
,
Pause
P
,
Record
P
and
Skip Up/Down
but-
tons to send commands to a different device
than the one that has been selected for other
commands. For example, you may wish to oper-
ate the transport of a second VCR you have con-
nected to the VID 2/TV input, as shown in the
following example.
1. Press and hold the
Program Button
&
for
about three seconds while the message shown
in Figure 15 appears in the remote’s
LCD
Information Display
2
. Release the but-
ton when the red light under the
Set Button
F
appears.
2. The remote’s
MAIN MENU
message (Figure
16), will appear in the LCD display and the
Set Button
F
will remain illuminated in
red. Press the
⁄¤
Navigation Buttons
E
until
PUNCH-THROUGH
appears on the bot-
tom line of the LCD screen, as shown in Figure
48. Press the
Set Button
F
to enter the
main punch-through menu branch.
3. At the next menu screen, press the
⁄¤
Navigation Buttons
E
until
TRANSPORT
appears on the bottom line of the LCD screen,
as shown in Figure 59. Press the
Set Button
F
to begin programming the remote for
transport punch-through.
Figure 59
4. The next display screen (Figure 60) is where
you select the device that will receive the
punch-through commands. In our example,
that is the TV button, as that is where we want
the VCR’s transport controls to be active. Press
the
⁄¤
Navigation Buttons
E
until the
name of the base device appears and then
press the
Set Button
F
.
Figure 60
5. At the next display screen (Figure 61), you will
select the device whose transport commands
will be used. Press the
⁄¤
Navigation
Buttons
E
until the desired device name
appears to the right of the device in use. In our
example, that is the VCR. When the desired
combination of devices appears, press the
Set
Button
F
.
Figure 61
6. When the Set button is pressed, the display
will change to show you that the new combi-
nation of control commands is being saved to
the unit’s memory, as shown in Figure 62. The
word
SAVED
will flash four times and then
the remote will return to normal operation.
Figure 62
7. Once the punch-through is programmed, the
transport buttons of the second device named
will be used when those buttons are pressed
while the master device is in use.
Returning the Transport Control Settings
to Default Operation:
If you wish to remove the Transport Punch-
Through so that the transport commands are
returned to the factory default setting, follow the
steps shown above, except that in Steps 4 and 5,
select the same device for both the
DEVICE IN
USE
on the left side of the bottom line and the
PUNCH-THROUGH
device. In the example used,
the display to return the remote to default set-
tings will appear as shown in Figure 63.
Figure 63
EzSet Configuration
Harman Kardon’s patented EzSet feature makes
it easier than ever to calibrate the output levels
on your new DPR for maximum playback accura-
cy. In addition to automatically setting the levels,
the DPR remote’s LCD display allows the unit to
be used as a direct read-out SPL meter. Complete
instructions for using the EzSet features of the
DPR remote are found on page 28 of this
owner’s manual.
In most cases you will find it easier to access the
EzSet capabilities directly by pressing the
SPL
Select Button
*
and following the menu
prompts as detailed in page 28. However, there
is one function of the remote that is only avail-
able through the remote’s menu system being
described in this section.
To avoid having the calibration settings created
with EzSet changed accidentally, the remote
allows you to disable the
SPL Select Button
*
on the remote. To de-activate the button,
follow these steps:
1. Press and hold the
Program Button
&
for
about three seconds while the message shown
in Figure 15 appears in the remote’s
LCD
Information Display
2
. Release the but-
ton when the red light under the
Set Button
F
appears.
2. The remote’s
MAIN MENU
message (Figure
16), will appear in the LCD display and the
Set Button
F
will remain illuminated in
red. Press the
⁄¤
Navigation Buttons
E
until
SET SPKR LEVELS
appears on the bot-
tom line of the LCD screen, as shown in Figure
64. Press the
Set Button
F
to enter the
main EzSet menu branch.
Figure 64
3. At the next menu screen (Figure 65) press the
⁄¤
Navigation Buttons
E
once so that
EZSET DISABLE
appears in the lower line of
the LCD display.
Figure 65
4. Within five seconds, press the
Set Button
F
to disable the
SPL Select Button
*
.
Once the
Set Button
F
is pressed the word
EXITING
will flash four times in the lower line
of the LCD display and then it will return to
normal operation.
Once these steps are completed, when the
SPL
Select Button
*
is pressed the remote will
show
EZSET DISABLE
and it will not be activat-
ed.
To restore the EzSet feature to normal operation,
repeat the procedure outlined above, except that
in step #3 you should press the
⁄¤
Navigation Buttons
E
so that
EZSET
ENABLE
appears in the lower line of the LCD
display. When that display appears, press the
Set
Button
F
and the EzSet feature will be reacti-
vated. You may then press the
Clear Button
#
to exit the remote’s menu system and return
to normal operation or press the
Set Button
F
again to immediately use the EzSet feature
to calibrate the system as shown on page 28.
S E T S P K R L E V E L S
E Z S E T D I S A B L E
M A I N M E N U
S E T S P K R L E V E L S
P U N C H - T H R O U G H
T V
<
- T V
T V
<
- V C R [ T R S ]
S A V E D
P U N C H - T H R O U G H
T V
<
- V C R
D E V I C E I N U S E
T V
P U N C H - T H R O U G H
T R A N S P O R T
P U N C H - T H R O U G H
V C R
<
- V C R