Harman Kardon AVR 445 Скачать руководство пользователя

Страница: 24 / 64

When all settings on this page are complete, press
the

⁄

Navigation Buttons

until the

on-screen cursor is pointing to

PAGE 1

and then

press the

Set Button

pœ

to return to the main

IN/OUT SETUP

menu to configure another

input, or if no further input configuration adjustments
are needed, press the

⁄

Navigation Buttons

until the on-screen cursor is pointing to

MASTER MENU

and then press the

Set Button

pœ

to return to the main menu screen.

Audio Setup

This menu allows you to configure the tone controls.
If you do not wish to change any of those settings at
this time, proceed to the next menu screen. To make
configuration changes to those parameters, first make
certain that the

MASTER MENU

is on screen

with the cursor pointing to the

AUDIO SETUP

line, and press the

Set Button

pœ

. The

AUDIO SETUP

menu (Figure 4) will appear.

Figure 4

The first line controls whether or not the bass/treble
tone controls are in the signal path. The normal default
is for them to be in-line, but if you wish to remove
them from the circuit for “flat” response, first make
certain that the cursor is pointing to the

TONE

line on the menu and press the

‹

›

Navigation

Buttons

so that

OUT

is highlighted.

If you wish to leave the tone controls in the signal
path, the amount off boost or cut for bass and treble
may be adjusted up to ±10dB in 2dB steps by press-
ing the

⁄

Navigation Buttons

that the cursor is next to

BASS

TREBLE

depending on which setting you wish to adjust. Next,
press the

‹

›

Navigation Buttons

until

the desired setting is shown.

When all desired changes have been made on this
menu, press the

⁄

Navigation Buttons

so that the cursor is next to the

BACK

TO MASTER MENU

line; press the

Set

Button

pœ

Surround Setup

The next step is to set the surround mode you wish
to use with the input that was previously selected in
the

IN/OUT SETUP

menu. Since surround

modes are a matter of personal taste, feel free to
select any mode you wish – you may change it later.
However, to make it easier to establish the initial
parameters for the AVR 445, we suggest Logic 7
(Cinema or Music) for most analog inputs. For inputs
such as a CD Player, Tape Deck or Tuner, you may
wish to set the mode to Stereo (“Surround Off”), as
they are not typically used with multichannel program
material, and it is unlikely that surround-encoded mate-
rial will be used. Alternatively, the Logic 7 Music mode
is a good choice for stereo-only source material. See
page 58 for information on surround modes.

For digital program material, the AVR will always exam-
ine the data stream and automatically select a Dolby
Digital or DTS mode, as applicable.

To begin the surround setup process, from the

MASTER MENU

(Figure 1), press the

⁄

Navigation Buttons

until the cursor is next

to the

SURROUND SETUP

line. Press the

Set Button

pœ

until the

SURROUND

SETUP

menu (Figure 5) is on the screen.

Figure 5

The first line on the menu allows you to select the
input for which the specific surround settings will
be applied. Press the

‹

›

Navigation Buttons

to select the input source to be configured.

The

AUDIO IN-PORT

and

AUDIO IN

lines are for display only and may not be changed
through the

SURROUND SETUP

menu. The

AUDIO IN-PORT

displays the physical con-

nection source for the current active input, and the

AUDIO IN

line shows the signal type present.

Note that an

UNLOCK

message in the

AUDIO

line indicates that a digital input has been selected

for that source, but that no data stream is present.

When the input selection has been made, press the

⁄

Navigation Buttons

to move to

the next configuration line.

The

ADC SAMPLING

line is where you deter-

mine whether the unit’s upsampling feature is turned
on or off. The default setting of

48kHz

puts the

feature in a bypass, or “off,” mode and will pass digital

audio data through the DSP at its native sample rate.
To process incoming 44.1kHz signals at a higher
resolution, upsampled 96kHz sample rate, press the

‹

›

Navigation Buttons

once so that

96kHz

appears.

When the desired setting has been made, or if no
adjustment is required at this line, press the

⁄

Navigation Buttons

to move to the next

configuration line.

The

SURR MODE

and

SURR SELECT

lines are related, as they guide you to the choice of
the surround mode that will be activated whenever the
input being configured is selected.

At the

SURR MODE

line, press the

‹

›

Navigation Buttons

to select the surround

mode group (such as Dolby modes, DTS modes,
Logic 7 modes, and DSP or Stereo modes) that is
applicable to the input source. After making a selec-
tion, press the

⁄

Navigation Buttons

to move to the

SURR SELECT

line.

At the

SURR SELECT

line, you are able to

choose the specific mode to be used from within the
major surround mode group. The choice of modes is
governed by the input type (as some modes such as
Dolby Digital or DTS-ES are not available for analog
sources), as well as by the speaker configuration,
since some modes are only available when a full 7.1
speaker complement is present. The full list of avail-
able modes is detailed in the surround mode chart on
page 60. Also, you may also use the settings in the

SURROUND CONFIG

menus to delete modes

you do not normally use from the available choices.

When both a surround mode group and a specific
surround mode have been selected, press the

⁄

Navigation Buttons

to move to the next

configuration line.

The

DEFAULT SURR

mode line is where you

choose the mode that is activated when a digital
source is selected.

LAST

will activate the last-used

mode for any digital source. If you prefer to always
have a digital source switch to the specific mode
encoded by digital data flags in the incoming audio
data stream, press the

‹

›

Navigation Buttons

so that

ORIGINAL

appears.

Before proceeding to the

SURROUND CONFIG

line, it is worth noting that the settings in the sub-
menus attached to that line may require a consider-
able amount of time to complete. Although they are
useful in that they allow you to customize the list of
surround modes that appear in normal use of the AVR,
you may wish to bypass those settings at this time so
that you may complete the configuration process. You
may return to this menu line at a later time, once you
have had a chance to listen to the various surround
modes and determine which you want to “keep” and
which you do not want to use. The settings in this line

SURROUND SETUP *

SOURCE: VIDEO 1
AUDIO IN PORT: ANALOG
AUDIO IN: PCM 44.1kHz
ADC SAMPLING: 48kHz
SURR MODE: LOGIC 7
SURR SELECT: MUSIC 5.1
DEFAULT SURR: ORIGINAL
SURROUND CONFIG
DOLBY SURR SETUP
BACK TO MASTER MENU

➔

AUDIO SETUP *

TONE :

OUT

BASS : 0
TREBLE: 0

BACK TO MASTER MENU

→

SYSTEM CONFIGURATION

AVR445 OM 6/23/06 3:13 PM Page 24