Hardi Mercury Series Скачать руководство пользователя страница 92

Страница: 92 / 114

6 - Maintenance

Apply thread sealant on the seat and screw it on the end of by-pass
hole up to beat. Use the socket wrench. Do not exceed with torque.

Apply the thread sealant on sleeve assembly, and tighten on valve
body up to beat using the wrench.

Tighten up to beat the stud B on the seat forcing lightly to obtain a
tighten connection.

Insert spring and lock into sleeve

Apply some lubricant inside handle. Place sealant at the end of stud
B thread and screw on handle C up to overlap the last notch on valve
body.

Screw on and lock up to beat the nut holding the handle while
tightening.

WARNING! To operate the gear motor unit 1, install 1.25A fuse
on12Vdc line.

The mark on lock A and gear motor cam must be aligned as
illustrated. These marks are referred to notch on gear motor
crankcase. To obtain the correct position, connect the brown cable to
+ pole of battery and the blue one to - pole.

Lubricate the gear motor crankcase and O Rings. Insert the gear
motor unit inside the valve body. The gear motor cap must beat on
valve body.

Assemble the lock.

Assemble all accessories and connect wiring.

ATTENTION! Brown cable to + pole to obtain this position

Содержание Mercury Series



















































































































Результаты поиска

Содержание Mercury Series

Отзывы:

Похожие инструкции для Mercury Series

Бренды по названию

Популярные бренды

Hardi Mercury Series, Инструкция

Результаты поиска

Содержание Mercury Series

Отзывы:

Похожие инструкции для Mercury Series

Бренды по названию

Популярные бренды