Hardi Mercury Series Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 114

background image

5 - Operation

70

Filling through tank lid

The tank is filled with water through the filling hole by removing the lid
located on the top of the tank. The water used should be as clean as
possible to obtain best results.

Fill the tank using the filter to prevent impuritie
h
s from entering the tank. For greater filling capacity, an overhead tank
can be used.

€

DANGER! Do not place the filling hose inside the tank. Keep it out
of the tank at all times and only point it towards the filling hole. If
the pressure hose were placed inside the tank and there was a
drop in water supply pressure, the chemical product could be
syphoned back and contaminate the water supply lines, plant and well.

μ

ATTENTION! The water supply line should be provided with a check valve as additional safety precaution. Follow local
legislation in force at any time.

μ

ATTENTION! The water supply should be provided with a meter to avoid spillage by over-filling. Follow local
legislation in force at any time.

Filling the rinsing tank

The rinsing tank is integrated with the main tank.

Capacity: 2000 and 3000 litres main tanks

The illustration shows the location of the rinse tank.

μ

ATTENTION! Not available on Mercury

μ

ATTENTION! Only fill rinsing tank with clean water! To avoid
algae developing in the rinsing tank always drain the rinsing
tank if the sprayer is not in use for a longer period of time.

Rinsing nozzle

This is to located inside the main tank. When the nozzle engaged it
rotates fast and spray clean water in all directions.

If the machine is fitted with a rinsing system, there are two rinsing
nozzles.

μ

ATTENTION! Not available on Mercury

HARDI

«
...
68
69
70
71
72
...
»

Содержание Mercury Series



















































































































Отзывы:

Нет отзывов

Похожие инструкции для Mercury Series

Бренд: T-Drill Страницы: 75

Бренд: Zeiss Страницы: 38

Бренд: Keithley Страницы: 32

Бренд: jcb Страницы: 166

Бренд: Cadman Страницы: 66

Бренд: OMCA Страницы: 36

Бренд: Salford Страницы: 64

Бренд: Bang & Olufsen Страницы: 2

Бренд: JBL Страницы: 38

Бренд: JBSYSTEMS Light Страницы: 32

Бренд: JBM Страницы: 12

Бренд: Octane Fitness Страницы: 20

Бренд: Oceaneering Страницы: 27

Бренд: Qlight Страницы: 3

Бренд: qtran Страницы: 2

Бренд: Q-Optics Страницы: 2

Marathon Multi600

Бренд: Saeyang Страницы: 21

Бренд: S&C Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды