Hardi Commander Twin Force Plus Скачать руководство пользователя страница 74

Страница: 74 / 94

GB 14 08 01

Maintenance

FFFFFan speed adjustment

an speed adjustment

(Bowden cable adjusted pumps only). The boom fan

speed base adjustments are carried out as follows.

A tachometer is required for this job.

1. Fit a piece of light-reflecting tape to the fan wing and

to the tractor P.T.O.

2. Unfold the boom to working position.

3. Set tractor P.T.O. at 540/1000 r.p.m. - check with the

tachometer.

4. Set the fan speed control lever to max. speed.

5. Measure the fan speed with the tachometer. The fan

speed must be 3100 r.p.m.

WARNING!

Do not wear loose hanging clothes!

Hold the tachometer firmly in your hands in order

not to be sucked into the fan. DO NOT REMOVE

THE PROTECTION GRID!

6. Turn the swash plate

adjustment screw

CW to decrease or

CCW to increase the

blower r.p.m.

Remember to tighten

the counter nut.

Repeat 3. and 4. until

the correct setting is

obtained.

7. If the correct fan r.p.m. cannot be reached, the

hydraulic transmission pressure settings must be

checked - see section on Fan transmission pressure

adjustment.

FFFFFan tr

an tr

an transmission priming

ansmission priming

If the hydraulic fan transmission has been dismantled, or

pump or motor has been changed, the following priming

procedure must be carried out before starting up the

transmission:

1. Fill the oil reservoir with fresh, clean oil to the top of

the sight glass.

2. Fill the pump housing with

oil through the drain pipe

which is dismantled at the

tank connection. Recon-

nect and tighten.

3. Check the oil level in the

gear box.

4. Remove the drain hose

from the motor outsidethe

blower housing.

5. Set the fan r.p.m. at 0,

engage the tractor P.T.O. with the engine running idle

- wait a few minutes.

6. Set the fan speed at 200 r.p.m.

7. After a while the oil will start dripping constantly. Refit

the drain hose and tighten.

8. With the tractor P.T.O. at 540/1000 r.p.m. the fan

should rotate at max. revolutions/min.

9. Recheck oil level at tank sight glass.

10.Check vacummeter at the suction filter.

11.Retighten hose connections and check for leaks.

12.Check fan speed and feed pressure adjustments -

see sections on Fan speed adjustment and Fan

transmission pressure adjustment.

FFFFFan tr

an tr

an transmission pr

ansmission pr

ansmission pressur

essur

essure adjustment

e adjustment

= Pressure port

= Return port

= Drain port

= Connector for working pressure measurement

= Connector for feed pressure

= Adjustment Screw for fed pressure

= Suction port

The transmission feed and working pressure are

checked as follows:

1. Connect a 40 bar (580 p.s.i.) pressure gauge to the

feed pressure connector

P2,

and a 400 bar (5800

p.s.i.) pressure gauge at the working pressure con-

nector

2. Set the tractor P.T.O. at 540/1000 r.p.m. - check with

tachometer.

3. Set the blower at max. speed.

4. Check the feed and working pressure:

T090-0002

T090-0003

T090-0005

T090-0002

Содержание Commander Twin Force Plus































































































Результаты поиска

Содержание Commander Twin Force Plus

Отзывы:

Похожие инструкции для Commander Twin Force Plus

Бренды по названию

Популярные бренды

Hardi Commander Twin Force Plus, Инструкция

Результаты поиска

Содержание Commander Twin Force Plus

Отзывы:

Похожие инструкции для Commander Twin Force Plus

Бренды по названию

Популярные бренды