Hardi Commander Twin Force Plus Скачать руководство пользователя страница 39

Страница: 39 / 94

GB 08 04

Operation

towards HARDI FILLER and the other green valve

towards agitation. Close remaining valves.

3. Check that bottom valve

at the FILLER is closed.

4. Engage the pump and set P.T.O. speed at 540 r/min

or 1000 r/min (depending on pump model).

5. Open FILLER lid.

6. Measure the correct quantity of chemical and fill it

into the hopper.

NOTE!

The scale in the hopper can only be used if the

sprayer is parked at level ground! It is recommended to

use a measuring jug for best accuracy.

7. Open the bottom valve

and the chemical is trans-

ferred to the main tank.

8. If the chemical container is empty it can be rinsed by

the container rinsing device (if fitted). Place the

container over the multi-hole nozzle and press the

lever

WARNING!

Do not press lever

unless the

multi-hole nozzle is covered by a container to

avoid spray liquid hitting the operator.

IMPORTANT!

Rinsing device uses spray liquid to rinse

containers for concentrated chemicals. Always rinse the

chemical containers with clean water several times until

they are clean before disposal.

9. Engage the hopper rinsing device by opening valve

10. Close valve

again when the hopper is rinsed.

IMPORTANT!

The hopper rinsing device is using spray

liquid for rinsing the hopper for concentrated chemical!

The FILLER must always be cleaned together with the

rest of the sprayer when the spray job is done.

11.Close valve

and the FILLER lid again.

12. When the spray liquid is well mixed, turn handle on

the Pressure Manifold towards Spraying position.

Keep P.T.O. engaged so the spray liquid is continu-

ously agitated until it has been sprayed on the crop.

Filling of Powder chemicals

1. Fill the main tank at least

with water (unless some-

thing else is stated on the

chemical container label).

See section Filling of

water.

2. Turn the handle at the

Suction Manifold

towards Main tank

and green valve

towards Agitation.

Turn the handle at

the Pressure Mani-

fold towards

HARDI FILLER.

Close remaining

valves.

3. Engage the pump

and increase

P.T.O. speed to

540 r/min or 1000 r/

min (depending on

pump model).

4. Open the bottom valve

the FILLER. Open FILLER lid.

5. Engage the hopper rinsing device by opening valve

6. Measure the correct quantity of chemical and sprinkle

it into the hopper as fast as the rinsing device can

flush it down.

7. If the chemical container is empty it can be rinsed by

the container rinsing device (if fitted). Fit the bag

bracket and place the powder bag over the multi-hole

nozzle and press the lever

WARNING!

Do not press lever

unless the

multi-hole nozzle is covered by a container to

avoid spray liquid hitting the operator.

IMPORTANT!

Rinsing device uses spray liquid to rinse

containers for concentrated chemicals. Always rinse the

chemical containers with clean water several times until

they are clean before disposal.

9. Close valve

again when the hopper is rinsed.

T042-0002

Black

Green

Black

Green

Содержание Commander Twin Force Plus































































































Результаты поиска

Содержание Commander Twin Force Plus

Отзывы:

Похожие инструкции для Commander Twin Force Plus

Бренды по названию

Популярные бренды

Hardi Commander Twin Force Plus, Инструкция

Результаты поиска

Содержание Commander Twin Force Plus

Отзывы:

Похожие инструкции для Commander Twin Force Plus

Бренды по названию

Популярные бренды