Hardi Commander Twin Force Plus Скачать руководство пользователя страница 69

Страница: 69 / 94

GB 14 08 01

Maintenance

T191-0012

Cone c

Cone chec

hec

heck/r

k/r

k/rene

ene

enew

wal,

al,

EVC distrib

C distrib

C distribution v

ution v

ution valv

alv

alveeeee

Periodically check the distribu-

tion valves for proper sealing.

Do this by running the sprayer

with clean water and open all

distribution valves.

Cautiously remove the clip

and pull out the hose

for the

pressure equalisation device.

When the housing is drained,

there should be no liquid flow

through the pressure equalisa-

tion device. If there is any

leakage, the valve cone

must

be changed.

Remove the clip

and lift the

motor housing off the valve

housing. Then unscrew the

screw

and replace the valve cone

. Reassemble in

reverse order.

Wear b

ear b

ear bush r

ush r

ush rene

ene

enew

wal, boom lift

al, boom lift

The wear bushes are inspected and renewed before

they are worn through.

1. Connect the trailer to a tractor and unfold the booms

to working position.

2. Lift the boom centre frame with a lifting device and

support it until the load is taken off the parallelogram

arms.

3. Remove the screws

, and pull out the pins

at one

of the upper parallelogram arms and renew the wear

bushes.

4. Refit the arm.

5. Repeat this on the other upper arm.

T251-0017

6. The lower arms must be disconnected simultane-

ously.

Grease all grease nipples.

7. Remove the lifting gear again.

Wear b

ear b

ear bush r

ush r

ush rene

ene

enew

wal, dr

al, dr

al, draaaaawbar

wbar

(all TRA

(all TRACKER models)

CKER models)

If too much play is found in the drawbar the wear

bushes must be renewed.

1. Place stop wedges in front of and behind both

wheels.

2. Jack up the frame and support it properly.

3. If

not

a SELF TRACK model: Remove the drawbar

extension to reduce the weight of the drawbar.

4. Loosen the two bolts

and support the bracket

order to keep it in a level position (e.g. by a rope

fastened to the platform railing).

5. Without dismantling the hydraulic system the hydrau-

lic rams are removed from the drawbar by loosening

the nuts

6. Support the drawbar and remove the two pin bolts

the washer

and the pin

7. Move the drawbar to the side and support it.

8. Press out the worn bushes and fit new ones.

9. Assemble again in reverse order.

10. Grease through grease nipples and remove jack

and wedges.

11. Fit the extension piece in the drawbar again and

place the sprayer on the support leg

Содержание Commander Twin Force Plus































































































Результаты поиска

Содержание Commander Twin Force Plus

Отзывы:

Похожие инструкции для Commander Twin Force Plus

Бренды по названию

Популярные бренды

Hardi Commander Twin Force Plus, Инструкция

Результаты поиска

Содержание Commander Twin Force Plus

Отзывы:

Похожие инструкции для Commander Twin Force Plus

Бренды по названию

Популярные бренды