Hardi Commander Twin Force Plus Скачать руководство пользователя страница 11

Страница: 11 / 94

GB 05 03 01

Sprayer setup

TTrrrrransmission shaft

ansmission shaft

Oper

Operaaaaator saf

tor saf

tor safety

ety

To avoid accidents and personal injuries, note the

following recommended precautions and safe operation

practices.

1. Always STOP ENGINE before attaching the transmis-

sion shaft to tractor P.T.O. - most tractor P.T.O. shafts

can be rotated by hand to facilitate spline alignment,

when engine is stopped.

2. When attaching the shaft, make sure that the snap

lock is FULLY ENGAGED - push and pull shaft until it

locks.

WARNING!

ROTATING TRANSMISSION

SHAFTS WITHOUT PROTECTION GUARDS

ARE FATAL.

3. Always keep protection guards and chains intact and

make sure that it covers all rotating parts, including

CV-joints at each end of the shaft. Do not use without

protection guard.

4. Do not touch or stand on the transmission shaft when

it is rotating - safety distance: 1.5 meter.

5. Prevent protection guards from rotating by attaching

the chains allowing sufficient slack for turns.

6. Make sure that protection guards around tractor

P.T.O. and implement shaft are intact.

7. Always STOP ENGINE and remove the ignition key

before carrying out maintenance or repairs to the

transmission shaft or implement.

Installa

Installation of

tion of

tion of tr

transmission shaft

ansmission shaft

First installation of the transmission shaft is done in the

following way:

1. Attach sprayer to tractor and set sprayer height in the

position with shortest distance between the tractor

and sprayer pump P.T.O. shafts.

2. Stop engine and remove ignition key.

3. If transmission shaft must be shortened, the shaft is

pulled apart.

Fit the two shaft parts at tractor and sprayer pump

and measure how much it is necessary to shorten the

shaft.

Mark the protection guards.

NOTE!

The shaft must always have a minimum overlap.

The size of this overlap depends on the pump model:

Pump with 6 splines/540 r.p.m.

The shaft must always have an overlap of minimum

1/3

of the length.

Pump with 21 splines/1000 r.p.m.

The shaft must always have an overlap of minimum

2/3

of the length.

4. The two parts are shortened equally. Use a saw, and

file the profiles afterwards to remove burrs.

5. Grease the tractor P.T.O. and pump shafts.

6. Fit the shaft to tractor P.T.O. and sprayer pump shaft.

NOTE:

Female part marked with a tractor towards

tractor!

T259-0004

T259-0005

T259-0007

T259-0011

Содержание Commander Twin Force Plus































































































Результаты поиска

Содержание Commander Twin Force Plus

Отзывы:

Похожие инструкции для Commander Twin Force Plus

Бренды по названию

Популярные бренды

Hardi Commander Twin Force Plus, Инструкция

Результаты поиска

Содержание Commander Twin Force Plus

Отзывы:

Похожие инструкции для Commander Twin Force Plus

Бренды по названию

Популярные бренды