Hardi Commander Twin Force Plus Скачать руководство пользователя страница 77

Страница: 77 / 94

GB 16 02

Fault-finding

FFFFFault-f

ault-f

ault-finding

inding

Oper

Operaaaaational pr

tional pr

tional prob

oblems

lems

In cases where breakdowns have occurred, the same factors always seem to be the problem:

1. Minor leaks on the suction side of the pump will reduce the pump capacity or stop the suction completely.

2. A clogged suction filter will hinder or prevent suction so that the pump does not operate satisfactorily.

3. Clogged up pressure filters will result in increasing pressure at the pressure gauge but lower pressure at the

nozzles.

4. Foreign bodies stuck in the pump valves with the result that these cannot close tightly against the valve seat. This

reduces pump efficiency.

5. Poorly reassembled pumps, especially diaphragm covers, will allow the pump to suck air resulting in reduced or

no capacity.

6. Hydraulic components that are contaminated with dirt result in rapid wear to the hydraulic system.

Therefore ALWAYS check:

Suction, pressure and nozzle filters are clean.

Hoses for leaks and cracks, paying particular attention to suction hoses.

Gaskets and O-rings are present and in good condition.

Pressure gauge is in good working order. Correct dosage depends on it.

Operating unit functions properly. Use clean water to check.

Hydraulic components are maintained clean.

FAULT

Sprayer trails unstable

Front hydraulic rams will

not allow the yoke to turn

when rear rams are

extended/retracted to the

maximum

Rear hydraulic rams are

too tight and vehicle

continues straight ahead

when trying to turn

TRA

TRACKER damping sy

CKER damping sy

CKER damping system

stem

PROBABLE CAUSE

Air pockets in the hydraulic

circuit

Hydraulic circuit leaking

Pressure relief valve(s) set too

low

Safety valve incorrectly ad-

justed

Insufficient counter weight on

front of tractor

Pressure relief valve set too

high

CONTROL/REMEDY

Prime hydraulic circuit

Repair leak, prime

Adjust pressure relief valves

Adjust safety valve

Ad ballast on front of tractor

Adjust pressure relief valves

Содержание Commander Twin Force Plus































































































Результаты поиска

Содержание Commander Twin Force Plus

Отзывы:

Похожие инструкции для Commander Twin Force Plus

Бренды по названию

Популярные бренды

Hardi Commander Twin Force Plus, Инструкция

Результаты поиска

Содержание Commander Twin Force Plus

Отзывы:

Похожие инструкции для Commander Twin Force Plus

Бренды по названию

Популярные бренды