Harbor Freight Tools PREDATOR 59134 Скачать руководство пользователя страница 24

Страница: 24 / 24

Page 24

For technical questions, please call 1-888-866-5797.

ITEM 59134

SAFETY

SETU
p

Op
ERA
TION

AINTENANCE

problem

possible Causes

probable Solutions

Product doesn’t

have power.

1. Product not plugged in properly.

2. Circuit Breaker tripped.

3. GFCI activated.

4. Product needs service.

1. Turn off and unplug the product, then

plug it back in again and turn on.

2. Turn off and unplug product. Reset Circuit

Breaker. Plug in product and turn on.

3. Turn off and unplug product. Test GFCI

receptacle. If functioning properly reset

GFCI, plug in product and turn on.

4. Have product repaired.

Product begins to

operate abnormally.

1. Problem with appliance.

2. Rated load capacity exceeded.

1. Immediately unplug appliance. Have

appliance repaired by a qualified

technician, or replace appliance.

2. Lower the number of items plugged into the

Generator to stay within the rated capacity,

or use a more powerful generator.

Follow all safety precautions whenever diagnosing or servicing the equipment or engine.

Troubleshooting (continued)

Содержание PREDATOR 59134

























Результаты поиска

Содержание PREDATOR 59134

Отзывы:

Похожие инструкции для PREDATOR 59134

Бренды по названию

Популярные бренды

Harbor Freight Tools PREDATOR 59134, Руководство пользователя

Результаты поиска

Содержание PREDATOR 59134

Отзывы:

Похожие инструкции для PREDATOR 59134

Бренды по названию

Популярные бренды