background image

Page 19

For technical questions, please call 1-888-866-5797.

ITEM 59134 

        

SAFETY

SETU

p

Op

ERA

TION

M

AINTENANCE

Checking and Filling Fuel

WARNING!

 

TO pREVENT SERIOUS 

INJURY FROM FIRE:

 

Fill tank in a well-ventilated area away 

from ignition sources.  If the engine 

is hot from use, shut the engine off and 

wait for it to cool before adding fuel.  Do not smoke.

1.  Clean the Fuel Cap and the area around it.

2.  Unscrew and remove the Fuel Cap.

Note:

 

Do not use gasoline containing more than 

10% ethanol (E10).  Do not use E85 ethanol.

Note:  Do not use gasoline that has been stored in a 

metal fuel container or a dirty fuel container.  It can 

cause particles to enter the carburetor, effecting 

engine performance and/or causing damage.

3.  If needed, fill the Fuel Tank to about 1 inch 

under the fill neck with 87 octane or higher 

unleaded gasoline that has been treated with 

a fuel stabilizer additive.  Follow fuel stabilizer 

manufacturer’s recommendations for use.

4.  Replace the Fuel Cap.

5.  Wipe up any spilled fuel and allow excess 

to evaporate before starting engine.  

To prevent FIRE, do not start the engine 

while the smell of fuel hangs in the air.

Engine Oil Change

CAUTION!

  Oil is very hot during operation and can 

cause burns.  Wait for engine to cool before changing oil.

1.  Make sure the engine is stopped and is level.

2.  Close the Fuel Valve.

3.  Place a drain pan (not included) underneath 

the crankcase’s drain plug.

4.  Remove the drain plug and, if possible, 

tilt the crankcase slightly to help drain 

the oil out.  Recycle used oil.

5.  Replace the drain plug and tighten it.

6.  Clean the top of the Dipstick and the area around it.  

Remove the Dipstick by threading it counterclockwise, 

and wipe it off with a clean lint free rag.

7. 

Full Level

Full Level

Add the appropriate type of oil until the  

oil level is at the full level.  SAE 10W-30 

oil is recommended for general use. 

Note:

 Do not thread the dipstick in 

when checking the oil level.

The SAE Viscosity Grade chart shows other 

viscosities to use in different average temperatures.

10W-30

30

5W-30

-20

0

20

40

60

80

100°F

SAE Viscosity Grades

Average outdoor temperature

8.  Thread the dipstick back in clockwise.

NOTICE:  Do not run the engine with too little oil.  

Engine will not start with low or no engine oil.

Air Filter Element Maintenance

1.  Remove the air filter cover and the air filter elements 

and check for dirt. Clean as described below.

2. 

Cleaning:

•  For “paper” filter elements: 

To prevent injury from dust and debris, wear 

ANSI-approved safety goggles, NIOSH-approved 

dust mask/respirator, and heavy-duty work gloves.  

In a well-ventilated area away from bystanders, 

use pressurized air to blow dust out of the air filter. 

If this does not get the filter clean, replace it.

•  For foam filter elements: 

Wash the element in warm water and mild 

detergent several times. Rinse. Squeeze out 

excess water and allow it to dry completely.  

Soak the filter in lightweight oil briefly, 

then squeeze out the excess oil.

3.  Install the cleaned filter.  Secure the 

Air Cleaner Cover before use.

Содержание PREDATOR 59134

























Отзывы: