HANGCHA CPCD10N-RW10 Скачать руководство пользователя | Manualshive

Страница: 39 / 108

background image

35

6. Operation

△

!

Warning!

Before operating the truck, check all

controls and warning devices for proper

operation. If any damage of fault is

found, don’t operate truck until corrected.

Star-up

Starting diesel engine

Make sure that the shift lever(s) and
loading levers are in neutral and hold
position.
Turn the ignition switch to ON position
after turning the ignition switch to
START position.

Caution

If you can not start the engine in 5

seconds, should switch to OFF, after 2
minutes then start it again.

If you can not start the engine 3

times continuously should check the
truck to the core.

Caution

If the temperature is lower than –5

degree, crank the engine by turning the
ignition key to “START”. Release key
when engine starts.

Starting gasoline engine

Make sure that the shift lever(s) and
loading levers are in neutral and hold
position.
Cold engine.

Pull out the choke button fully.

Depress the accelerator pedal to the
floor two or three times and release it.
With your foot OFF the pedal, crank the
engine by turning the ignition key to

“START”. Release key when engine
starts.
Warm engine

Do not pull out the choke button.

Press down the accelerator pedal
halfway and cold. Crank the engine by
turning the ignition key to “START”.
Release key when engine starts.

Caution

Do not press down the accelerator

pedal fully when starting warm engine.
This operation may harden the engine
starting. Pressing down the accelerator
pedal several times will cause harder
starting.

Caution

The starting time should less than 5

seconds a time, the interval between two
starting should much than 2 minutes.

After engine has started

Warm up the engine (for about 5

minutes)
Check the rotation (sound or gear) of
the engine.

Caution

Diesel model

After starring up the engine,

accelerate it’s speed to the arrange of
1800-2000r/min, and warm it without
work.

Gas model

After cranking the engine, push in

the choke button step by step observing
the warm-up condition and stability of
speed of the engine. Push in the choke
button fully after making sure the engine
is completely warmed up.

·Check the combustion (or misfiring)
sound.
·Check the condition (density) of

«
...
37
38
39
40
41
...
»

Содержание CPCD10N-RW10













































































































Отзывы:

Нет отзывов

Похожие инструкции для CPCD10N-RW10

EcoMaxx ECO-FD 18

Бренд: Starke Страницы: 48

Бренд: Baoli Страницы: 102

Drexel SLT30 AC

Бренд: Landoll Страницы: 90

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды