HAMPTON BAY H27U-NG Скачать руководство пользователя страница 14

Страница: 14 / 56

Hampton

H27U-NG/H27U-LP Direct Vent Freestanding Gas Stove

installation

Ground /Green

White

Neutral

Live

Black

Red

Black

Fan Thermodisc

(normally open)

(120V AC)

Rotary Speed

Control

Green

Ground

OFF

Fan

WARNING: Electrical Grounding Instructions

This appliance is equipped with a three pronged (grounding) plug for your protection against shock hazard and should be
plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from this plug.

11)

Mount the blower assembly in position under the base of the stove

and secure with the 2 supplied bolts (2-1/4" #20 hex head).

12)

Before re-attaching the rear access panel, connect live wire (black/

from fan) to black wire 704 (from speed controller). Use the clip wire
holders to organize the wires.

13)

Slide the Rear Access Panel back into position. Make sure the wires

are not blocking the passage of the relief door. Secure with 2 screws.

Tighten the 2 bolts

10)

Slide the thermodisc into the bracket on the left side of the rear firebox.

Connect the black wire 811 (90 degrees) & red (straight, from speed
controller) wires to the thermodisc.

Thermodisc

Braket

Clip Wire

Holders

Live Wire Black
(from fan) & Black
Wire 704 (labeled)

Relief

Door

Grounding lug in fan:

Ground wire to fan

Nut

Split/Lock washer

Ground wire to unit

Star washer

Nut

Ground from power cord

Grounding lug in unit:

Nut

Split/Lock washer

Star washer

Ground wire from fan

Содержание H27U-NG

























































Результаты поиска

Содержание H27U-NG

Отзывы:

Бренды по названию

Популярные бренды

HAMPTON BAY H27U-NG, Инструкция для владельца и по установке

Результаты поиска

Содержание H27U-NG

Отзывы:

Бренды по названию

Популярные бренды