HAMPTON BAY H27U-LP, Инструкция для владельца и по установке

Страница: 43 / 56

43
Hampton ® H27U-NG/H27U-LP Direct Vent Freestanding Gas Stove
maintenance
Lift Rear Panel off the 2 top bolts
bolts
screws screws
2) Remove the rear access panel on the back of
the stove by removing the 2 screws under the
rear panel, then lift off the 2 screws at the top.
Take care not to cut wires when lowering the
panel.
1) Unplug or disconnect power source to stove.
Fan Maintenance
If your fan requires maintenance or replacement,
access to the fan is through the rear access panel
on the back of the unit.
NOTE: the unit MUST
NOT be operated without the fan access panel
securely in place and correctly sealed.
IMPORTANT: These fans collect a lot of dust
from within your home. Ensure you maintain
these fan motors on a regular basis by vacuum-
ing out the fan squirrel cages, around the motor,
and around the grills on the back of the stove.
To Remove Fan:
IMPORTANT
Disconnect power supply
before servicing
Conduct an inspection of the venting system semi-
annually. Recommended areas to inspect as follows:
1) Check the Venting System for corrosion in areas
that are exposed to the elements. These will
appear as rust spots or streaks, and in extreme
cases, holes. These components should be
replaced immediately.
2)
Remove the Cap, and shine a flashlight down
the Vent. Remove any bird nests, or other foreign
material.
3) Check for evidences of excessive condensation,
such as water droplets forming in the inner
liner, and subsequently dripping out the joints,
Continuous condensation can cause corrosion
of caps, pipe, and fittings. It may be caused
by having excessive lateral runs, too many
elbows, and exterior portions of the system
being exposed to cold weather.
4) Inspect joints, to verify that no pipe sections or
fittings have been disturbed, and consequently
loosened. Also check mechanical supports such
as Wall Straps, or plumbers' tape for rigidity.
5) Verify proper operation after servicing.
Log Replacement
The unit should never be used with broken logs. Turn
off the gas valve and allow the unit to cool before
opening door to carefully remove the logs. The pilot
light generates enough heat to burn someone. If
for any reason a log should need replacement, you
must use the proper replacement log. The position
of these logs must be as shown in the diagram
under Log Installation.
Note: Improper positioning of logs may create
carbon build-up and will alter the unit’s
performance which is not covered under
warranty.
Glass Replacement
Your stove is supplied with high temperature, 5
mm Neoceram ceramic glass that will withstand the
highest heat that your unit will produce. In the event
that you break your glass by impact, purchase your
replacement door from an authorized Hampton
®
dealer only, and follow our step-by-step instructions
for replacement.
1) Lift off the Cast Top.
2) Open front access panel and remove 2 - 7/16"
bolts from locations shown below.
3) Lift the Glass Front Assembly up.
4 ) a) Remove the glass and replace with the new
glass.
b) Remove logs and replace the newer logs.
WARNING:
Electrical Grounding Instructions
This appliance is equipped with
a three pronged (grounding) plug
for your protection against shock
hazard and should be plugged
directly into a properly grounded
three-prong receptacle. Do not cut
or remove the grounding prong
from this plug.
5) Reinstall the door and Cast Front and Top.
7) Lift off Cast Front - place on a soft surface.
8) On top of firebox - undo 2 latches.
Replacement Part # 946-327
Glass
WARNING:
Do not operate appliance with
glass panel removed, cracked or broken. Re-
placement of the glass should be done by a
licensed or qualified service person.
Note: Wearing gloves will protect your hands
while handling glass.
6)
Remove the 2 - 7/16" bolts which secure the top
of the cast front on both the left and right side
as shown.