HAMPTON BAY H27U-LP, Инструкция для владельца и по установке

Страница: 24 / 56

24
Hampton ® H27U-NG/H27U-LP Direct Vent Freestanding Gas Stove
installation
DV Stove Horizontal Vent Kit (#946-116 & #946-216) Installation
Review the following sequence of instructions which are typical of most installations. The sequence may vary depending on wall thickness. See the "Exterior
Vent Terminal Locations" section for vent
location and clearance dimensions, and "Vent
Restrictor Position" section to set the Vent
Restrictor to the correct position.
1) Set the unit in its desired location. Check to
determine if wall studs will be in the way of the
venting system, adjust location until all clear-
ances are met and there are no obstructions.
Note: A 1-1/2"(38mm) clearance around the
outer pipe must be maintained except
that only a 1" (25mm) clearance is
needed at the termination end.
IMPORTANT:
Do not locate termination hood where ex -
cessive snow or ice buildup may occur. Be
sure to check vent termination area after
snow falls, and clear to prevent accidental
blockage of venting system. When using
snow blowers, make sure snow is not
directed towards vent termination area.
2) Assemble a trial fit to determine the vertical
centerline for the vent termination.
a) Cut a 9-1/2" x 9-1/2" (241mm x 241 mm)
square hole on both the interior and ex-
terior wall.
b) Install wall thimbles on both interior and
exterior wall with 4 wood screws (#8 x
1") per thimble.
c) Attach the 2 piece adjustable pipe sec-
tion to the vent terminal and slide into
position from the exterior.
Adapter
Trim Collar
4" ID Liner
Spacer
Spring
Thimble
Cover
Termination Cap
(Part# 946-523/P)
AstroCap
Wall Thimble
(required for
combustible walls)
Adjustable Pipe
Length 13-1/2" - 24",
2 pieces
4 ft. Pipe Length
with Kit # 946-216
or 2 ft. Pipe Length with
Kit # 946-116
Trim
Collar
DV Stove Horizontal Vent Kit
DV 2 ft. Stove Vent Kit (Part # 946-116) and DV 4 ft. Stove Vent Kit (946-216) includes all the parts needed
to install the H27U-NG Direct Vent unit with minimum horizontal and vertical vent dimensions. For installations
that require longer vertical and/or horizontal vents use the Dura-Vent system as shown in the "Dura-Vent
Termination Kit" and "Dura-Vent Venting Components" sections.
Qty. Description
1) 1 Rigid Pipe Section (Kit # 946-116: 2 ft. (1.2m) length,
Kit # 946-216: 4 ft. (1.2m) length), 6-1/2" (165mm)
inside diameter
2)
1 Flex Liner, compressed aluminium 2 ply liner, 4" (102mm)
inside diameter
3) 4 spring spacers
4)
1 90 deg. Elbow
5) 1 Adjustable pipe section 13-1/2" to 24" (343mm x 610mm), 2 pcs.
6)
1 Thimble Cover
7) 1 Wall Thimble (2 pcs.)
8) 1 Adapter
9)
1
AstroCap
Termination Cap
10) 2 Trim Collars
11)
1 Tube of Mill-Pac, high temperature sealant
12) 12 Screws, #8 x 1/2" Self tapping, Stainless Steel
13) 14 Screws, #8 x 1/2" Self tapping, Black
14)
4 Screws #8 x 1-1/2" Drill Point, Black
15) 4 Screws #8 x 1-1/2" Drill Point, Stainless Steel
16) 8 Wood screws #8 x 1"
Note:
a) Liner sections should be continu-
ous without any joints or seams.
b) This is an approved system, there-
fore components in this system
must not be substituted for any
other manufacturer's products.
The larger diameter end of the adjustable
pipe goes to the vent terminal.
d) Install the 90
o
elbow onto the adjustable pipe
to determine the vertical centerline.
Note: if the centerline cannot be met, the
adjustable sections will have to be cut.
e) Cut the 4 ft. section of rigid pipe to length.
Attach the 45
o
elbow to the rigid pipe, and
ensure that the pipe length when cut (with
the 45
o
elbow) will seat onto both the starter
collar and the 90
o
elbow. Crimped section
of rigid pipe seats into the 90
o
elbow. Only
cut the uncrimped side of pipe.
Dismantle all pipe sections including vent terminal.
3) Attach the 4" dia. flex liner to the vent terminal
ensuring that the flex overlaps the collar of the
vent terminal by a minimum of 1-3/8"(35mm). Use
Mill-Pac to seal and secure with 3 of the #8 x 1/2"
screws (stainless steel).
4) Attach the adjustable pipe section to the vent
terminal using Mill-Pac and/or high temperature
silicone and attach with 3 of the #8 x 1/2" screws
(stainless steel).