HAMPTON BAY H27U-LP Скачать руководство пользователя страница 28

28

Hampton

®

 H27U-NG/H27U-LP Direct Vent Freestanding Gas Stove

installation

You  will  require  the  following  components  with 
your new  Direct Vent Freestanding Gas Stove. 
Please  review  your  product  to  make  sure  you 
have everything you need. In the event that you 
are missing any part, contact your dealer. 

Note:  These  are  the  minimum  pieces  re

-

quired. Other parts may be required for 

your particular installation. See above 

for a list of vent parts.

If installing termination on a siding covered wall, 
a  vinyl  siding  standoff  or  furring  strips  can  be 
used  in  order  to  ensure  that  the  termination  is 
not recessed into siding.

The vinyl siding standoff is required for walls with 
vinyl siding.

Minimum components for a Dura-Vent
Horizontal Installation:

A)  Dura-Vent Horizontal Termination Kit
B)  Wall Thimble (required for combustible walls)

Minimum components for a Dura-Vent
Vertical Termination:

D)  Dura-Vent Vertical Termination Kit. See above 

for pipe lengths.

Diagram 2a

Horizontal Terminations

1)

  Set the unit in its desired location. Check to 

determine if wall studs are in the way when 
the venting system is attached. If this is the 
case, you may want to adjust the location of 
the unit.

2)

  Assemble  the  desired  combination  of  pipe 

and elbow to the appliance adapter with pipe 
seams oriented down. Offset the pipe seams 
as double seams in one place will cause the 
outer pipe to take an oval shape. Kit comes 
complete with 18" of straight vent - 6-5/8" dia. 
black outer pipe and 4" dia. inner vent. 

3)

  With the pipe attached to the stove, slide the 

stove into its correct location, and mark the 
wall for a   9-1/2" (inside dimensions) round 
hole. The center of the round hole should line 
up with the centerline of the horizontal pipe, 
as  shown  in  diagram  1.  Cut  and  frame  the 
9-1/2  round  hole  in  the  exterior  wall  where 
the vent will be terminated. If the wall being 
penetrated is constructed of non-combustible 
material, i.e. masonry block or concrete, a  7" 
diameter hole is acceptable.

a)

  The  horizontal  run  of  vent  should  have  a            

1/4 inch rise for every 1 foot of run towards 
the termination. Never allow the vent to run 
downward. This could cause high tempera-
tures and may present the possibility of a 
fire.

b)

  The location of the horizontal vent termina-

tion on an exterior wall must meet all local 
and national building codes, and must not be 
blocked or obstructed. Refer to the "Exterior 
Vent Terminal Locations" section.

c)

 

Snorkel Terminations:

 

For  installations  requiring  a  vertical  rise 
on the exterior of the building, 14-inch and 
36-inch tall Snorkel Terminations as shown 
in Diagram 2 are available, as well as the 
standard  Riser  Vent.  Follow  the  same  in-
stallation procedures as used for standard 
Horizontal Termination.  NEVER  install  the 
snorkel upside down.

 

Diagram 1

*Diagram 2a: As specified in CGA B149 Instal-
lation  Code.  Local  codes  or  regulations  may 
require different clearances.

Diagram 2b

NOTE: For Snorkel terminations  in ABOVE  grade 

installations, follow national or local code 

requirements.

 

 Below Grade Snorkel Installation

       If the Snorkel Termination must be installed below 

grade, i.e. basement application, proper drainage 
must  be  provided  to  prevent  water  from  enter-
ing the Snorkel Termination. Refer to Installation 
instructions for details.. Do not attempt to enclose 
the  Snorkel  within  the  wall,  or  any  other  type  of 
enclosure.

4)

  Install wall penetration heat shield in the center of 

the 9-1/2" round hole and attach with wood screws. 
The four wood screws provided should be replaced 
with appropriate fasteners for stucco, brick, concrete, 
or other types of sidings. Diagram 3.

5)

   If installing termination on a siding covered wall, a 

vinyl siding standoff or furring strips must be used 
to ensure that the termination is not recessed into 
the siding.  Diagram 3.

6)

  Take the Riser Vent terminal and separate the Back-

ing Plate from the Riser Vent Front by removing 8 
screws as shown in diagram 4.

Diagram  3

Содержание H27U-LP

























































Отзывы: