background image

 

 

 

WARNING:

 

This unit emits ultraviolet (UV) radiation that is harmful to humans.  Avoid exposure 

to the direct or reflected output beam.  Make certain that the appropriate output beam shields and 

optics are in place prior to energizing the unit.  All interlocks must be satisfied prior to operation; 

failure to do so may lead to hazardous conditions. 

 

 

CAUTION: 

The TLS-EQ-77H emits dangerous levels of UV radiation.  Even short exposures to 

skin or eyes may cause burns.  Ensure that only authorized personnel are in the vicinity of source 

during operation.  Personnel in vicinity of operating source should wear protective eyewear, 

clothing, and gloves.  Lighted UV warning lights and signs posted on doors to lab areas may help 

prevent accidental exposure.   

 

 

 

 

WARNING:

 

The TLS-EQ-77H utilizes an internal Class 4 IR laser capable of causing severe injury 

to eyes or skin.  Do not open or attempt to service this unit.  Contact Energetiq regarding any 

problems with the unit. 

 

 

WARNING: 

When working near the emitted light, always wear protective devices (conforming to ISO 

4007/4849/4850/4854/4855 or equivalent regulations). The lamp installed in this housing emits intense ultraviolet rays, 

which are harmful to the eyes and skin. Looking directly into the emitted light or allowing the light to fall on the skin will 

damage eyesight or cause skin burns.

  

 

WARNING: 

If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment 

may be impaired. 

The power supply must be properly grounded by the outlet to prevent electrical shocks. 

Securely plug in the power supply connector to avoid looseness or play. Loose connections may result in 

faulty operation. 

2.1.1  Definition of equipment and document symbols and designations 

Do not operate the TLS-EQ-77H if the covers are removed or is defective in any way.  Contact Energetiq if 

any problems with the equipment are suspected. 

The TLS-EQ-77H utilizes a quartz lamp containing a high-pressure gas fill.  Explosion of the lamp 

and possible injury from flying fragments can occur if the lamp is mishandled.   

Do not open the enclosure of either the Lamp or the Controller.  Dangerous invisible infrared laser 

beams and hazardous voltages exist inside the Lamp.  

Opening the chassis both voids the warranty and 

exposes the user to dangerous radiation and hazardous voltages. 

 

 

 

 

CAUTION: 

controls or adjustments or performance of procedures other than those specified 

herein may result in hazardous radiation exposure

.

 

 

 

 

 

WARNING:

 

Invisible laser radiation avoid eye or skin exposure to direct or scattered radiation 

Class 1 laser product 

Содержание ENERGETIQ LDTLS TLS-EQ-77H














































Отзывы: