Haier GE GDF510P M0 Series Скачать руководство пользователя страница 34

Страница: 34 / 40

– 34 –

Top Control Console Cover Removal

1. Remove and separate the door.

2. Remove the bottom cover, UI, light pipe and

buttons.

3. Remove the top console and cover as an

assembly.  There are six 1/4-inch hex-head
screws, securing the assembly to the inner
door (note the length of the screws).  A new
cover should be replaced in the event the
cover is loose or must be removed.  The tabs
are likely to break on removal.

1. The top cover is secured with sixteen tabs,

and the console has cutouts or slots to allow
the top cover to click lock together.

2. Position the tabs on the cover into the slots

on the console.

3. Press the top and console securely together

and slide the parts to engage the tabs into the
slots. Start from one end and work across to

will be heard as the cover and console snap
together.

Six 1/4 in. hex-

head screws

5. The light pipe separates from the bottom

cover with tabs. A small screwdriver may be

release the remaining tabs (four each side).

7. With the light pipe removed, the UI may be

lifted out of the bottom cover.

When replacing UI control boards, the new UI

included with the replacement. If the
personality is not set by using the 4 jumpers,

properly.

are found in the

Electronic Control

section

of this service guide.

Top Control Console Cover

Содержание GE GDF510P M0 Series









































Результаты поиска

Содержание GE GDF510P M0 Series

Отзывы:

Похожие инструкции для GE GDF510P M0 Series

Бренды по названию

Популярные бренды

Haier GE GDF510P M0 Series, Техническое обслуживание руководство

Результаты поиска

Содержание GE GDF510P M0 Series

Отзывы:

Похожие инструкции для GE GDF510P M0 Series

Бренды по названию

Популярные бренды