background image

– 2 –

Safety Information

IMPORTANT SAFETY NOTICE

The  information  in  this  service  guide  is  intended  for  use  by 
individuals  possessing  adequate  backgrounds  of  electrical, 
electronic,  and  mechanical  experience. Any  attempt  to  repair  a 
major  appliance  may  result  in  personal  injury  and  property 
damage. The manufacturer or seller cannot be responsible for the 
interpretation of this information, nor can it assume any liability in 

connection with its use.

WARNING

To  avoid  personal  injury,  disconnect  power  before  servicing 
this  product.  If  electrical  power  is  required  for  diagnosis  or  test 
purposes, disconnect the power immediately  after performing the 

necessary checks.

RECONNECT ALL GROUNDING DEVICES

If grounding wires, screws, straps, clips, nuts, or washers used to 
complete a path to ground are removed for service, they must be 

returned to their original position and properly fastened.

GE Appliances, a Haier Company

Copyright © 2018

All rights reserved. This service guide may not be 

reproduced in whole or in part in any form without written 

permission from GE Appliances, a Haier Company.

For Warranty Information: 

1.  Go to http://products.geappliances.com

2.  Search the model number.
3.  Click on the Literature tab.

4.  Click on Use and Care Manual.

5.  Locate the Warranty page.

Warranty

Содержание GE GDF510P M0 Series









































Отзывы: