Haier GE GDF510P M0 Series Скачать руководство пользователя страница 36

Страница: 36 / 40

– 36 –

1. Remove the door.

2. Place the door on a protected surface to

prevent damage.

3. On plastic inner door models, slide the gasket

either direction to remove. The door does not
need to be separated on plastic inner doors.

4. On SS Inner Door models, the inner door

panel has the door gasket riveted to the panel.

The inner door panel must be replaced to

replace the door gasket.

End View

Console Insulation

Gasket

Vent

Conduit

Gasket

Handle

Bracket

and Grill

Insulation

Gasket

Vent

Conduit

Gasket

Insulation

Front Panel

Door Gasket

Front Control Models

Top Control Models

The detergent module is Solenoid operated, using
13.5 VDC to activate the solenoid.

The GDF510PxJxx and GDT535PxJxx send 13.5

VDC from the main control under the Dishwasher.

All other models send the 13.5 VDC from the UI

board in the door.

Some models have a rinse agent dispenser.

The dispenser holds 3.5 oz. (100 ml) of rinse

agent. Under normal conditions, this will last
approximately one month.

The module receives 13.5 VDC for .5 seconds to

activate the detergent cup. To activate the rinse
aid the module receives 13.5 VDC for a period of

15 seconds.

Remove power to dishwasher.

Remove toe kick panel.

Disconnect door harness.

The resistance for the detergent module

checked at the module or the door harness as
it enters the bottom of the main control board.
Connector J401 pins 2 AX (

aqua

) to 4 CW

(

brown

white

). Board connector and pin out

is found in the

Electronic Controls

section of

this service guide. Voltage may be checked
during service mode.

Содержание GE GDF510P M0 Series









































Результаты поиска

Содержание GE GDF510P M0 Series

Отзывы:

Похожие инструкции для GE GDF510P M0 Series

Бренды по названию

Популярные бренды

Haier GE GDF510P M0 Series, Техническое обслуживание руководство

Результаты поиска

Содержание GE GDF510P M0 Series

Отзывы:

Похожие инструкции для GE GDF510P M0 Series

Бренды по названию

Популярные бренды